New Arrivals

SKU: SF-COM-10468 | Brand: SparkFun

The MSGEQ7 is a CMOS graphic equaliser IC that divides the audio spectrum into seven frequency bands: 63 Hz, 160 Hz, 400 Hz, 1 kHz, 2.5 kHz, 6.25 kHz, and 16 kHz. Each band is peak-detected and multiplexed to provide ...

SKU: AF-574 | Brand: Adafruit

Put a current meter anywhere with this very handy display. This panel meter requires a DC voltage to run, and then has two thick gauge wires to measure current draw. A shunt is already on board so its very easy to hoo...

SKU: AF-576 | Brand: Adafruit

Put a temperature meter anywhere with this very handy display. This panel meter displays the temperature of the attached waterproof 1% thermistor in °C. It does require a DC voltage to run, at 4.5-30VDC. It has revers...

SKU: SF-ROB-10456 | Brand: SparkFun

This 12V DC solenoid valve controls water flow through a 3/4″ threaded inlet and outlet. It is normally closed — fluid is blocked until 12V is applied to the fast-on spade connectors on the solenoid coil. Connect it t...

SKU: SF-ROB-10455 | Brand: SparkFun

The SEAFLO mini water pump is a submersible 12 V pump capable of moving up to 1325 litres per hour (350 GPH). Powered by a heavy-duty 1.5 A motor housed in a tough thermoplastic body, it handles continuous operation i...

SKU: SF-PRT-10454 | Brand: SparkFun

Standard 4-40 zinc-plated hex nuts. A common thread size used in electronics enclosures, PCB mounting, and small hardware assemblies. Specifications Thread Size – 4-40 (UNC) Material – Zinc-plated steel Quantity ...

SKU: DF-DFR0376 | Brand: DFRobot

INTRODUCTION OCELL is a 0.5" micro OLED display designed for Arduino and other microcontrollers. This micro OLED display is small as the grown-up's fingernail- 0.5" only. It has 450cd/m^2 sc...

SKU: DF-FIT0452 | Brand: DFRobot

A 2-way lever-action wire connector made from flame-retardant material. These connectors provide a quick, solderless way to join wires — simply lift the lever, insert the stripped wire, and push the lever down to lock...

SKU: DF-FIT0453 | Brand: DFRobot

A GSM antenna with SMA connector and magnetic base for easy mounting on ferrous metal surfaces. The 3 m extension cable uses 174 pure copper construction for low impedance, and the antenna provides 2.5 dBi signal gain...

SKU: SF-COM-12792 | Brand: SparkFun

This is a 2x40 pin right-angle PTH header. This header can be broken apart with a fair amount of force to form smaller header formations. Don’t worry, it’s easy enough to break it where you need! Each pin has a spa...

SKU: SF-PRT-12790 | Brand: SparkFun

This is a 2x23 pin female PTH header, with extra long legs which makes great for stacking. This piece is in the common configuration for Beaglebone Black headers. Each pin has a spacing of 0.1" in between each othe...

SKU: SF-ROB-10391 | Brand: SparkFun

A linear push-type solenoid rated for 36 V DC that also works well at 12 V. Solenoids produce linear motion for pushing, pulling, or actuating switches and levers. This unit has a measured throw of approximately 10 mm...

SKU: SF-PRT-10375 | Brand: SparkFun

This is a simple five wire cable. Great for jumping from board to board or just about anything else. There is a 5-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway hea...

SKU: AF-3306 | Brand: Adafruit

Fire up your engines because these are the hot-rods of toggle switches! Equipped with an aerodynamic blue protective casing, and a diffused blue LED at the tip of the switch, this Blue LED Toggle Switch is s...

SKU: SF-PRT-10372 | Brand: SparkFun

This is a simple two wire cable. Great for jumping from board to board or just about anything else. There is a 2-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway headers...

SKU: AF-1827 | Brand: Adafruit

Make your own USB connections without slicing apart a USB cable and soldering those thin wires inside. This is the 'slim' version of the DIY USB-A Male connector. It's a little more elegant because instead of snapp...

SKU: AF-1813 | Brand: Adafruit

A 10-segment LED bar graph display in a warm amber colour. At just 1" (25mm) long, it's compact enough to plug directly into a breadboard while remaining clearly visible. The diffused rectangular lenses give a clean, ...

SKU: DF-KIT0098 | Brand: DFRobot

INTRODUCTION Breadboard-Plugin Components Pack is a new kit designed for breadboard experiment. It provides many kinds of components, such as resistors, capacitors, diodes, transistor .et...

SKU: SF-PRT-10361 | Brand: SparkFun

This is a simple six wire cable. Great for jumping from board to board or just about anything else. These cables mate with the connectors listed below. They have bare wires on one end and a 6-pin JST SH connector on t...

SKU: SF-ROB-10335 | Brand: SparkFun

This pan/tilt bracket kit includes two brackets and all the hardware needed to build a pan/tilt mechanism using two servo motors. Perfect for mounting cameras, sensors, or other small payloads that need two-axis posit...