New Arrivals

SKU: AF-1164 | Brand: Adafruit

This breakout board will solve all your current-monitoring problems. Instead of struggling with a multimeter, you can just use the handy INA169 chip on this breakout to both measure both the DC current draw and have a...

SKU: AF-1374 | Brand: Adafruit

This breakout board is the simplest way to create a project with a single "momentary" capacitive touch sensor. No microcontroller is required here - just power with 1.8 to 5.5VDC and touch the pad to activate the sens...

SKU: AF-3709 | Brand: Adafruit

The Adafruit SGP30 is a multi-pixel MOX (metal-oxide) gas sensor from Sensirion that measures Total Volatile Organic Compounds (TVOC) and equivalent CO2 (eCO2) for indoor air quality monitoring. With fully calibrated ...

SKU: DF-SEN0232 | Brand: DFRobot

The Gravity Analog Sound Level Meter is an Arduino-compatible decibel meter that accurately measures environmental noise levels. It uses an instrumentation-grade circuit with a low-noise microphone for high-precision ...

SKU: AF-1770 | Brand: Adafruit

The 2.8" TFT LCD Breakout Board features a bright, full-colour display with a resistive touchscreen and an onboard MicroSD card socket. With 240×320 resolution and individual RGB pixel control, it delivers vivid colou...

SKU: AF-1782 | Brand: Adafruit

This I2C digital temperature sensor is one of the more accurate/precise we've ever seen, with a typical accuracy of ±0.25°C over the sensor's -40°C to +125°C range and precision of +0.0625°C. They work great with any ...

SKU: DF-SEN0097 | Brand: DFRobot

This is a BH1750 light intensity sensor breakout board with a 16 bit AD converter built-in which can directly output a digital signal, there is no need for complicated calculations. This is a more acurate and easier ...

SKU: DF-DFR0164 | Brand: DFRobot

This is a new version of the FTDI breakout board features an Atmega8U2 programmed as a USB-to-serial converter, the same chip found on the Arduino Uno. The 8U2 firmware uses the standard USB COM drivers, and no ...

SKU: SF-BOB-11771 | Brand: SparkFun

This is a breakout board for the Texas Instruments TXB0104 module. The TXB0104 is a 4-bit bidirectional voltage-level translator with automatic direction sensing. This 4-bit noninverting translator uses two separate...

SKU: AF-3070 | Brand: Adafruit

The Adafruit RFM69HCW Transceiver Radio Breakout @ 868/915 MHz is a breadboard-friendly packet radio module for adding long-range wireless communication to Arduino and other microcontroller projects. Based on the SX12...

SKU: SF-DEV-13743 | Brand: SparkFun

The SparkFun Level Shifting microSD Breakout is quite similar to the SparkFun microSD Transflash Breakout, but with the included level shifting hardware, this board allows you to utilize a microSD card at Arduino’s SD...

SKU: SF-SEN-11574 | Brand: SparkFun

Heart rate data can be really useful whether you’re designing an exercise routine, studying your activity or anxiety levels or just want your shirt to blink with your heart beat. The problem is that heart rate can be ...

SKU: SF-BOB-13717 | Brand: SparkFun

This is the SparkFun Pi Wedge, a small board that connects to the 40-pin GPIO connector on the Raspberry Pi and breaks the pins out to breadboard-friendly arrangement and spacing, and even adds a couple of decou...

SKU: AF-284 | Brand: Adafruit

Note: These use genuine FTDI chips, either we purchase them or they are manufactured to our specifications with the requirement of genuine FTDI chips 10/22/14 - read more. Long gone are the days of parallel ports and ...

SKU: AF-444 | Brand: Adafruit

Add a tiny joystick to your project with this PSP thumbstick. This is a replacement component for PSP1000's, but we think they'd make for a great little joystick/thumbstick add-on for a wearable, or portable pro...

SKU: DF-SEN0162 | Brand: DFRobot

The Gravity Analog UV Sensor V2 uses a GUVA-S12SD photodiode to detect ultraviolet radiation in the 200–370 nm (UV-A) wavelength range. It outputs a linear analogue voltage signal proportional to UV intensity, making ...

SKU: SF-SEN-12642 | Brand: SparkFun

The SparkFun Sound Detector is a small and very easy to use audio sensing board with three different outputs. The Sound Detector not only provides an audio output, but also a binary indication of the presence of so...

SKU: AF-1918 | Brand: Adafruit

An analog UV light sensor breakout based on the GUVA-S12SD photodiode, detecting the 240–370nm range covering UVB and most of the UVA spectrum. An on-board op-amp amplifies the tiny photodiode current to a readable vo...

SKU: AF-3533 | Brand: Adafruit

The Adafruit 0.96" 160×80 Colour TFT Display Breakout is a tiny, high-density full-colour screen driven by the ST7735R controller. Despite its thumbnail size, it packs 160×80 RGB pixels and communicates over 4-wire SP...

SKU: SF-BOB-29094 | Brand: SparkFun

A breakout board for the Panasonic EVQWGD001 roller wheel encoder with press-to-select switch. This tactile input device combines a scrolling wheel with a push button in a compact form factor – similar to the scroll w...