New Arrivals

SKU: SF-PRT-15353 | Brand: SparkFun

Sometimes we want our projects on, but sometimes we want to turn them off for a while to save power. The SparkFun Nano Power Timer will run while only consuming minimal power (approximately 35nA) and turn your project...

SKU: AF-4197 | Brand: Adafruit

Add a crisp, paper-like display to your microcontroller project with the Adafruit 2.13" Monochrome eInk Breakout. This 250×122 pixel black-and-white eInk panel delivers excellent daylight readability and retains its i...

SKU: DF-TEL0119 | Brand: DFRobot

The USB/TTL Raspberry Pi GPS Tracker is a compact GPS location module built around the L80-39 chip. With 66 search channels and 22 simultaneous tracking channels, it delivers fast satellite acquisition and reliable po...

SKU: SF-ROB-14450 | Brand: SparkFun

The TB6612FNG Motor Driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes: CW, CCW, short-bra...

SKU: AF-1164 | Brand: Adafruit

This breakout board will solve all your current-monitoring problems. Instead of struggling with a multimeter, you can just use the handy INA169 chip on this breakout to both measure both the DC current draw and have a...

SKU: AF-1374 | Brand: Adafruit

This breakout board is the simplest way to create a project with a single "momentary" capacitive touch sensor. No microcontroller is required here - just power with 1.8 to 5.5VDC and touch the pad to activate the sens...

SKU: PI-COM1700 | Brand: Pimoroni

The AM2320 is a digital temperature and humidity sensor with an I2C interface. Its straightforward I2C communication makes it easy to connect to any Raspberry Pi or Arduino, and it works alongside other I2C sensors an...

SKU: AF-3709 | Brand: Adafruit

The Adafruit SGP30 is a multi-pixel MOX (metal-oxide) gas sensor from Sensirion that measures Total Volatile Organic Compounds (TVOC) and equivalent CO2 (eCO2) for indoor air quality monitoring. With fully calibrated ...

SKU: DF-SEN0232 | Brand: DFRobot

The Gravity Analog Sound Level Meter is an Arduino-compatible decibel meter that accurately measures environmental noise levels. It uses an instrumentation-grade circuit with a low-noise microphone for high-precision ...

SKU: AF-1782 | Brand: Adafruit

This I2C digital temperature sensor is one of the more accurate/precise we've ever seen, with a typical accuracy of ±0.25°C over the sensor's -40°C to +125°C range and precision of +0.0625°C. They work great with any ...

SKU: PL-2490 | Brand: Pololu

This sensor is a carrier/breakout board for ST’s VL53L0X laser-ranging sensor, which measures the range to a target object up to 2 m away. The VL53L0X uses time-of-flight measurements of infrared pulses for rangi...

SKU: DF-SEN0097 | Brand: DFRobot

This is a BH1750 light intensity sensor breakout board with a 16 bit AD converter built-in which can directly output a digital signal, there is no need for complicated calculations. This is a more acurate and easier ...

SKU: DF-DFR0164 | Brand: DFRobot

This is a new version of the FTDI breakout board features an Atmega8U2 programmed as a USB-to-serial converter, the same chip found on the Arduino Uno. The 8U2 firmware uses the standard USB COM drivers, and no ...

SKU: SF-BOB-11771 | Brand: SparkFun

This is a breakout board for the Texas Instruments TXB0104 module. The TXB0104 is a 4-bit bidirectional voltage-level translator with automatic direction sensing. This 4-bit noninverting translator uses two separate...

SKU: AF-3070 | Brand: Adafruit

The Adafruit RFM69HCW Transceiver Radio Breakout @ 868/915 MHz is a breadboard-friendly packet radio module for adding long-range wireless communication to Arduino and other microcontroller projects. Based on the SX12...

SKU: SF-BOB-13717 | Brand: SparkFun

This is the SparkFun Pi Wedge, a small board that connects to the 40-pin GPIO connector on the Raspberry Pi and breaks the pins out to breadboard-friendly arrangement and spacing, and even adds a couple of decou...

SKU: AF-284 | Brand: Adafruit

Note: These use genuine FTDI chips, either we purchase them or they are manufactured to our specifications with the requirement of genuine FTDI chips 10/22/14 - read more. Long gone are the days of parallel ports and ...

SKU: AF-444 | Brand: Adafruit

Add a tiny joystick to your project with this PSP thumbstick. This is a replacement component for PSP1000's, but we think they'd make for a great little joystick/thumbstick add-on for a wearable, or portable pro...

SKU: DF-SEN0162 | Brand: DFRobot

The Gravity Analog UV Sensor V2 uses a GUVA-S12SD photodiode to detect ultraviolet radiation in the 200–370 nm (UV-A) wavelength range. It outputs a linear analogue voltage signal proportional to UV intensity, making ...

SKU: AF-1897 | Brand: Adafruit

The Adafruit SPI Non-Volatile FRAM Breakout provides 64 Kbit (8 KBytes) of ferroelectric RAM (FRAM) storage over SPI. FRAM combines the non-volatile retention of flash with the instant read/write speed of SRAM — no pa...