New Arrivals

SKU: DF-FIT0297 | Brand: DFRobot

This is a 600mm (23.62") servo extension cable. This comes in very handy when your servo is further away from the controller than the wire on the servo allows. Male connector on one end goes to controller, female c...

SKU: SF-COM-08636 | Brand: SparkFun

The MCP3002 is a 10-bit analog-to-digital converter (ADC) with a simple SPI interface, available in a breadboard-friendly 8-pin DIP package. Use it to add analog input capability to microcontrollers that lack an ADC, ...

SKU: SF-COM-08589 | Brand: SparkFun

This is a simple, very common rectifier diode. Often used for reverse voltage protection, the 1N4001 is a staple for many power, DC to DC step up, and breadboard projects. 1N4001 is rated for up to 1A/50V. If you ne...

SKU: AF-2897 | Brand: Adafruit

A simple adapter that sits inside a 5.5 / 2.5 mm DC barrel jack, allowing you to use a standard 5.5 / 2.1 mm barrel plug with it. Just insert the adapter into the device's 2.5 mm jack, then plug in your 2.1 mm power s...

SKU: SF-PRT-08432 | Brand: SparkFun

Screw Terminals with 5mm pitch pins. Comes in 2 or 3 positions and have the really cool feature of slide-locking together to form any size you need (4, 5, up to 20 without problems). Rated up to 300V @ 8A. Terminal...

SKU: SF-DEV-14013 | Brand: SparkFun

A pack of five red LilyPad LEDs on a snap-apart strip. Each LED has large sew tabs for stitching into fabric with conductive thread, making them ideal for wearable electronics and e-textile projects. The ultra-thin 0....

SKU: DF-FIT0317 | Brand: DFRobot

This DVI to HDMI converter is a convenient module for those using Embedded boards and testing on old monitors, It can be used just fine with other monitors or graphic cards as well. SPECIFICATIONS DV...

SKU: SF-COM-11899 | Brand: SparkFun

Muscle Wire is a shape memory alloy (Nitinol — nickel-titanium) that contracts when heated or when an electrical current is applied, then returns to its original length when cooled. This property makes it useful as a ...

SKU: SF-COM-00527 | Brand: SparkFun

The LM317TG is a three-terminal adjustable positive voltage regulator with an output range of 1.2V to 37V and up to 1.5A output current. Only two external resistors are needed to set the desired output voltage, making...

SKU: SF-COM-00315 | Brand: SparkFun

The SN754410 is a quad half H-bridge motor driver IC capable of driving DC motors, stepper motors, and other inductive loads. It accepts TTL 5V logic inputs and can drive motors from 4.5V to 36V at up to 1A continuous...

SKU: SF-SEN-00246 | Brand: SparkFun

This sensor uses an infrared emitted diode combined with an infrared phototransistor to detect the reflected infrared signal. Ideal for sensing black-to-white transitions or can be used to detect nearby objects (.5-1cm).

SKU: SF-WRL-00145 | Brand: SparkFun

A 2.4 GHz rubber duck antenna with 2.2 dBi gain and a reverse-polarity SMA (RP-SMA) connector. At 100 mm (4″) long with 50 Ω impedance, it's a straightforward way to add an external antenna to WiFi, Bluetooth, ZigBee,...

SKU: DF-DRI0023 | Brand: DFRobot

INTRODUCTION Do you want to do some projects with stepper motors such as a drafting instrument, a 3D printer, an auto curtain......? As we all know, regular stepper motors are hard to dri...

SKU: SF-PRT-11476 | Brand: SparkFun

This barrel jack plug is great for adding a common connector to the end of our wires. This jack is compatible with 5.5mm barrel jacks that have a 2.1mm center pole diameter. The outer shell unscrews to reveal solder t...

SKU: DF-DFR0023 | Brand: DFRobot

This is an Arduino Temperature Sensor based on LM35 temperature chip. A Temperature Sensor can be used to detect ambient air temperature.The LM35 chip is produced by National Semiconductor Corporation and offers a fun...

SKU: AF-184 | Brand: Adafruit

Build your own breadboard-friendly adjustable power supply with this soldering kit. Based on the MIC2941 low-dropout regulator, it provides a guaranteed 1.25A output with only 40–400 mV dropout — far better than the L...

SKU: SF-PRT-11417 | Brand: SparkFun

These headers are made to work with the Arduino Uno R3, Leonardo and new Arduino boards going forward. They are the perfect height for clearing the USB-B connector and great for stacking multiple shields. This kit ...

SKU: SF-PRT-11375 | Brand: SparkFun

An assortment of colored wires: you know it’s a beautiful thing. Six different colors of stranded wire in a cardboard dispenser box. Sit this on your workbench and stop worrying about having a piece of wire around!Fea...

SKU: DF-DFR0165 | Brand: DFRobot

Say goodbye to messy cables and clueless pluging/unpluging! This Sensor Shield is a powerful expansion shield for Arduino Mega Due. It is large enough to carry up to 3 Xbee slots, 1 microSD slot and shield headers...

SKU: SF-DEV-11364 | Brand: SparkFun

The LilyTwinkle is a tiny little LilyPad board designed to add some twinkle to your project. Even though it’s as small as some of the LilyPad sensors, this board actually has an ATtiny microcontroller on it so it’s...