Headers & Connectors

SKU: SF-BOB-12035 | Brand: SparkFun

Add a Micro-B USB connector to your project without the hassle of soldering tiny SMD pads. This compact breakout board routes all five pins — VCC, GND, ID, D−, and D+ — to a standard 0.1" pitch header for easy breadbo...

SKU: SF-WRL-00593 | Brand: SparkFun

PCB edge mount - SMA RF connector. Perfect for prototyping with the GPS and Cellular devices that require an antenna connection. These connectors have a female signal pin and will correctly mate with the original SMA ...

SKU: AF-3009 | Brand: Adafruit

Short break-away male headers in a convenient pack of ten — ideal for low-profile connections where standard-height male headers would be too tall. These headers are designed to pair with short female headers for a sl...

SKU: SF-CAB-13685 | Brand: SparkFun

This is a simple jumper adapter cable that comes pre-terminated with a female JST connector on one end and a breadboard hookup pigtail on the other. This cable makes it easy to connect components with a JST connector ...

SKU: AF-3143 | Brand: Adafruit

A pack of small dual-row connector housings for building custom jumper cable harnesses. Compatible with standard 0.1" pitch raw jumper wire crimp pins — snap in your crimped wires and create exactly the connector conf...

SKU: PL-1015 | Brand: Pololu

This single-row, 5-pin straight female header with 0.1" (2.54mm) pitch is designed to mate with standard 0.1" male headers. It provides a reliable socket connection for board-to-board and board-to-wire applications. ...

SKU: PL-1907 | Brand: Pololu

These 1×8-pin crimp connector housings let you quickly build custom cables that mate with standard 0.1" (2.54mm) spaced connectors. Pair them with pre-crimped terminal wires to create reliable, removable eight-wire co...

SKU: PL-1905 | Brand: Pololu

These 1×6-pin crimp connector housings let you quickly build custom cables that mate with standard 0.1" (2.54mm) spaced connectors. Pair them with pre-crimped terminal wires to create reliable, removable six-wire conn...

SKU: SF-PRT-12639 | Brand: SparkFun

A 3.5mm TRRS (tip, ring, ring, sleeve) audio jack in a surface-mount package. Unlike standard stereo TRS connectors, TRRS provides three conductors plus ground, allowing it to carry stereo audio along with an addition...

SKU: AF-724 | Brand: Adafruit

Screw terminal blocks are the clean, maintainable solution for PCB-to-wire connections — no solder, no loose ends, easy to swap out later. These 3.5mm pitch 2-pin blocks are a practical size: wide enough for a range o...

SKU: AF-816 | Brand: Adafruit

These right-angle male headers feature a 3-row configuration at standard 0.1" (2.54mm) pitch, making them ideal for connecting three-wire cables such as sensor and servo leads. Each piece is a 3×4 block, and four piec...

SKU: SF-PRT-08431 | Brand: SparkFun

This is a SparkFun exclusive! These are 155mm long jumpers with male connectors on both ends. Use these to jumper from any female header on any board, to any other female header. Combine these with our female to femal...

SKU: LB-LS5179-5 | Brand: Little Bird

A pack of ten 5-pin PCB screw terminal blocks with a 2.54mm (0.1") pitch — the same spacing as standard breadboard headers. Strip a wire, insert it into the terminal, and tighten the screw for a secure, solderless ele...

SKU: AF-5360 | Brand: Adafruit

A magnetic pogo pin connector set with three 0.1" (2.54mm) spaced contact pins in a right-angle configuration. The two halves snap together via embedded magnets, ensuring all three pogo pins make reliable contact. If ...

SKU: DF-FIT0852 | Brand: DFRobot

This DIN Rail RJ45 Terminal Block Adapter-Horizontal, perfect for simplifying complex wiring, consists of an RJ45 Ethernet jack and an eight-port terminal. You can connect an RJ45 Ethernet to PCB which can be DIN rai...

SKU: AF-4423 | Brand: Adafruit

Totaling 560 pieces, this JST-XH Connector Kit is a must-have for your workstation. You'll have enough sockets and headers to fuel your maker tendencies for days on end!These connectors are really ...

SKU: AF-4208 | Brand: Adafruit

A 10-pack of JST SH 4-pin right-angle connectors with 1 mm pitch through-hole mounting tabs. These are the standard connectors used with the Qwiic and STEMMA QT ecosystems, making it easy to add I2C connectivity to yo...

SKU: SF-PRT-15187 | Brand: SparkFun

These stackable headers are made to work with the SparkFun ESP32 Thing Plus to connect to shield with a Feather footprint. This set includes one 12-pin and one 16-pin header; the pins are spaced by 0.1".Each set of he...

SKU: AF-2141 | Brand: Adafruit

A compact 8-pin screw terminal block with 2.54mm (0.1") pitch, designed to fit directly into perfboard and protoboards. Terminal blocks provide reliable, tool-adjustable PCB-to-wire connections that are easy to mainta...

SKU: AF-3629 | Brand: Adafruit

A solderless breakout adapter that connects a USB-A female socket to a 5-pin screw terminal block. Simply use a small screwdriver to open the terminal blocks, slide in your stranded or solid-core wire, and tighten — n...