Headers & Connectors

SKU: SF-BOB-15100 | Brand: SparkFun

Add a USB-C connector to your project without wrestling with tiny SMD pads. This breakout board routes the USB-C connector's key pins to a standard 0.1" pitch header, making it straightforward to integrate into breadb...

SKU: AF-3642 | Brand: Adafruit

A 2.1 mm DC barrel jack with a built-in slide switch, giving you simple on/off control for devices that lack a dedicated power switch. It shares the same PCB footprint as a standard non-switched barrel jack, so it dro...

SKU: SF-BOB-14021 | Brand: SparkFun

This is the SparkFun RJ11 Breakout, two simple breakout boards for the common 6-pin RJ11 connector. These little boards can easily have one of our RJ11 6-Pin Connectors to work with common telephone cables. Each bo...

SKU: SF-PRT-08272 | Brand: SparkFun

This 2 mm pitch 10-pin socket mates with XBee radio modules from Digi, allowing you to mount your XBee without soldering it directly to a PCB. You'll need two of these sockets to connect to all 20 pins on an XBee modu...

SKU: SF-PRT-00132 | Brand: SparkFun

Through-hole RJ11 socket with PCB mounting posts. 6-pin connection - housing accepts common telephone connectors/wiring. If you need a board for this connector be sure to check out our SparkFun RJ11 Breakout. Two b...

SKU: DF-FIT0365 | Brand: DFRobot

 INTRODUCTION Premium quality jumper wires for prototyping. Made with 26AWG multi-strand wire and sturdy male pins. Each jumper wire is approximately 210mm in length. Each pack comes with 30 jumper wires in a...

SKU: SF-PRT-10897 | Brand: SparkFun

These are 155mm long jumpers terminated as male to male. Use these to jumper from any female header on any board, to any other female header. Multiple jumpers can be installed next to one another on a 0.1" header. Com...

SKU: SF-PRT-10571 | Brand: SparkFun

These are simple 2-position screw terminals with 2.54mm pitch pins. Rated up to 150V @ 6A, this terminal can accept 30 to 18AWG wire. The 2.54mm pitch will line up with standard 0.1" perf boards.Documents: Datasheet

SKU: SF-PRT-09749 | Brand: SparkFun

A 2-pin right-angle JST PH series connector for through-hole PCB mounting. With a 2 mm pin pitch, this is the standard connector used on most single-cell LiPo batteries, making it ideal for battery-powered projects an...

SKU: DF-FIT0849 | Brand: DFRobot

This Ethernet RJ45 Female Plug to 8-Pin Terminal Block provides a solder-free way to break out an RJ45 Ethernet connection to individual screw terminals. The standard RJ45 port features a metal shielding layer for ele...

SKU: DF-FIT0861 | Brand: DFRobot

A set of five solderless snap-down connectors for joining 10 mm wide, 3-wire LED strips without soldering. Simply align the strip's copper pads with the connector contacts and snap the cover down for a firm electrical...

SKU: DF-FIT0867 | Brand: DFRobot

A set of five solderless right-angle connectors for joining 10 mm wide, 3-wire LED strips at 90° corners. Each connector has snap-down contacts on both ends with colour-labelled wires and marked polarity for easy, too...

SKU: AF-4748 | Brand: Adafruit

A 150-piece assortment of spade quick-connect terminals in three common sizes, complete with matching insulating sheaths. These crimp-on connectors are widely used in electronics for fast, secure connections to micro ...

SKU: AF-3893 | Brand: Adafruit

The JST PH 3-Pin to Male Header Cable converts a JST PH 3-pin connector into three individual colour-coded wires, each terminated with a 0.1" (2.54 mm) male header pin. It's ideal for extending sensor or LED connectio...

SKU: AF-3647 | Brand: Adafruit

Precision-machined Swiss-pin male plug headers for a tight, reliable fit. Unlike standard stamped square-pin male headers, these use machined round pins that pair exclusively with Swiss-pin female sockets — they are n...

SKU: AF-3662 | Brand: Adafruit

If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers from Pimoroni might be just what you need.  Absolutely no soldering required! All t...

SKU: AF-1131 | Brand: Adafruit

A 500 mm extension cable with a JST-PH 2-pin socket on one end and a matching plug on the other. The colour-coded wires make it easy to verify correct polarity. Compatible with JST-PH terminated battery packs includin...

SKU: AF-4031 | Brand: Adafruit

Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a stereo jack so you get left and right channels as well as a ground pin. You can use any 3.5mm stereo cable with this jac...

SKU: AF-1663 | Brand: Adafruit

A matching pair of 3-pin JST SM connector cables — one plug and one receptacle — for creating quick-connect/disconnect points in 3-wire circuits. The locking latch keeps the connection secure while still allowing easy...

SKU: AF-2430 | Brand: Adafruit

Pogo pins are little spring-loaded contacts, very handy for making jigs, or making momentary (but electrically solid) contacts. We use them by the dozen for making programming and testing jigs but they're handy also i...