Enclosures & Hardware

SKU: DF-FIT0195 | Brand: DFRobot

A 10-pack of M3 × 6mm clear nylon screws with matching nuts. Transparent and non-conductive, these fasteners are ideal for applications requiring electrical insulation, corrosion resistance, and a clean visual appeara...

SKU: DF-FIT0203 | Brand: DFRobot

This is a very basic double sided prototyping board with standard 0.1" spacing through holes and four 3mm diameter mounting holes. There are 22x26 holes in total. Great for quickly prototyping stackable circuit...

SKU: SF-PRT-09173 | Brand: SparkFun

These spring-loaded pogo pins with round tips are ideal for programming jigs, test fixtures, and temporary connections where you don't want to solder permanent headers. The pins fit snugly into standard perfboard hole...

SKU: DF-FIT0223 | Brand: DFRobot

A medium-sized aluminium heat sink with pre-applied 3M 8810 thermal adhesive tape on the back. Simply peel off the blue protective film and stick it directly onto your IC or chip — no thermal paste or glue required. T...

SKU: DF-FIT0294 | Brand: DFRobot

A 10-pack of M3 × 6mm low-profile hex head cap screws with matching nuts. The hex socket drive provides a more secure fastening than standard Phillips or slot-head screws, and the low-profile head sits flush for a cle...

SKU: DF-DFR0224 | Brand: DFRobot

The Arduino Screwless Terminal Shield breaks out all Arduino Uno-compatible header pins to spring-loaded push-in terminal blocks. Press the lever, insert your wire, and release — no screwdriver needed. The shield stac...

SKU: DF-FIT0273 | Brand: DFRobot

A 10-pack of M3 × 16mm low-profile hex head cap screws with matching nuts. The hex socket drive provides a more secure fastening than standard Phillips or slot-head screws, and the low-profile head sits flush for a cl...

SKU: SF-COM-11840 | Brand: SparkFun

These snap-in plastic LED holders provide a clean, secure way to panel-mount 5 mm LEDs. Simply press the LED into the holder and snap the holder into a 7.5 mm (19/64″) mounting hole — no screws or adhesive required. T...

SKU: SF-CAB-00508 | Brand: SparkFun

These are various leaded cables for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. High quality coax cable with stress relief sleeves. Dimensions: 36" long

SKU: SF-PRT-11796 | Brand: SparkFun

These nylon standoffs are ¾" long and tapped for a 4-40 screw. These are great for mounting your board in an enclosure, or just getting it up off the table. The black nylon will give your project a very sessy look. ...

SKU: AF-275 | Brand: Adafruit

By popular demand! We now have the plates from the ARDX available separately. Acrylic plate is engraved and cut here at the Adafruit factory. There are mounting holes for your Arduino and a space that fits a half s...

SKU: SF-PRT-10454 | Brand: SparkFun

Standard 4-40 zinc-plated hex nuts. A common thread size used in electronics enclosures, PCB mounting, and small hardware assemblies. Specifications Thread Size – 4-40 (UNC) Material – Zinc-plated steel Quantity ...

SKU: DF-FIT0474 | Brand: DFRobot

A transparent acrylic enclosure for the LattePanda single board computer. The case protects the board from ESD damage while the clear acrylic lets you view indicator LEDs directly. All ports are easily accessible incl...

SKU: AF-762 | Brand: Adafruit

A PG-7 cable gland for creating weatherproof cable pass-throughs in enclosures. Install over your power, data, or sensor cables and the gland forms a seal around the cable, keeping moisture and debris out of your proj...

SKU: SF-COM-09773 | Brand: SparkFun

This is a 5mm PTH fuse clip intended to be used with our Glass Fuses. Note: These are sold in single units. If you intend to secure a fuse using these clips you’ll need two clips. We recommend ordering two. Part #: ...

SKU: DF-FIT0064 | Brand: DFRobot

A 10-pack of M3 × 50mm hexagonal standoffs with matching screws and nuts. Use them to mount circuit boards, sensors, and other components with consistent 50mm spacing and secure mechanical support. At 50mm height, th...

SKU: AF-4631 | Brand: Adafruit

A pack of four magnetic mounting feet designed for RGB LED matrix panels. At 16.6 mm long, each magnet-screw slots into the standard 3 mm mounting bosses found on most RGB matrix panels, providing a quick and secure w...

SKU: LB-LS7583 | Brand: Little Bird

A compact dual-fan cooling module for enclosures, 3D-printed builds, network gear, and DIY electronics. Two matched 70×70×15mm fans provide effective airflow and heat dissipation, powered via USB for simple plug-and-g...

SKU: LB-LS7538 | Brand: Little Bird

A sturdy metal mounting bracket for servos, providing a stable platform for robotics and motion projects. Precision-cut mounting holes ensure secure servo installation for joints, linkages, arms, and custom assemblies...

SKU: AF-6433 | Brand: Adafruit

Keep your Adafruit MagTag safe and looking sharp with this custom-designed 3D-printed enclosure. The snap-together two-piece case accommodates all connection ports and features flexible push tabs for the four front bu...