Components

SKU: SF-PRT-10372 | Brand: SparkFun

This is a simple two wire cable. Great for jumping from board to board or just about anything else. There is a 2-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway headers...

SKU: AF-1827 | Brand: Adafruit

Make your own USB connections without slicing apart a USB cable and soldering those thin wires inside. This is the 'slim' version of the DIY USB-A Male connector. It's a little more elegant because instead of snapp...

SKU: AF-1813 | Brand: Adafruit

A 10-segment LED bar graph display in a warm amber colour. At just 1" (25mm) long, it's compact enough to plug directly into a breadboard while remaining clearly visible. The diffused rectangular lenses give a clean, ...

SKU: DF-KIT0098 | Brand: DFRobot

INTRODUCTION Breadboard-Plugin Components Pack is a new kit designed for breadboard experiment. It provides many kinds of components, such as resistors, capacitors, diodes, transistor .et...

SKU: SF-PRT-10361 | Brand: SparkFun

This is a simple six wire cable. Great for jumping from board to board or just about anything else. These cables mate with the connectors listed below. They have bare wires on one end and a 6-pin JST SH connector on t...

SKU: SF-COM-12766 | Brand: SparkFun

The L7812 is a three-terminal positive voltage regulator with a fixed 12V output. It provides stable local regulation with built-in protection against overcurrent, thermal overload, and short circuits, making it a rel...

SKU: SF-PRT-10287 | Brand: SparkFun

This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm, center-positive male barrel jack. If you need to connect bare wires to a barrel jack...

SKU: AF-1856 | Brand: Adafruit

What's better than a single LED? Lots of LEDs! Matrices like these are 'multiplexed' - so to control 64 LEDs you need 16 pins. That's a lot of pins, and there are driver chips like the MAX7219 that can control a...

SKU: AF-1897 | Brand: Adafruit

The Adafruit SPI Non-Volatile FRAM Breakout provides 64 Kbit (8 KBytes) of ferroelectric RAM (FRAM) storage over SPI. FRAM combines the non-volatile retention of flash with the instant read/write speed of SRAM — no pa...

SKU: AF-1800 | Brand: Adafruit

A solder-on 3.5 mm (1/8") stereo audio plug for building custom audio cables. Made from durable metal with a flexible spring strain relief, it provides a solid, professional-quality connection. Solder your wires to th...

SKU: AF-3428 | Brand: Adafruit

A voltage detector is handy for projects where you want to make sure your microcontroller doesn't run at a low voltage. For example, say you have a Feather Huzzah running on a lipoly battery every few minutes. Even...

SKU: AF-680 | Brand: Adafruit

These 5mm diffused RGB LEDs feature a built-in controller chip that automatically cycles through colours in a fast flashing pattern — no microcontroller or programming required. With just two leads (power and ground),...

SKU: SF-BOB-10160 | Brand: SparkFun

Here is a real time clock based on the DS3234 Real Time Clock IC. The DS3234 is a low-cost, extremely accurate SPI bus real-time clock with an integrated temperature-compensated crystal oscillator and crystal. Th...

SKU: DF-FIT0425 | Brand: DFRobot

The ECell Breadboard-Plugin LED pack contains 8 colour-coded LEDs mounted on gold-plated breadboard-compatible modules. Each module has clearly marked polarity and circuit symbols, making it easy to identify component...

SKU: DF-FIT0423 | Brand: DFRobot

INTRODUCTION Introducing "The Breadboard-Plugin Kit" - the first kit in the ECell series. The Breadboard-Plugin Kit provides a range of common components such as resistors, capacitors,...

SKU: AF-705 | Brand: Adafruit

A compact 3-wire voltage meter with a vivid green 3-digit 7-segment display. Reads 0–99.9VDC with 0.1V precision, making it perfect for monitoring battery levels, power supplies, and electronic projects. Mounting tabs...

SKU: AF-1865 | Brand: Adafruit

This is a great connector for anyone doing RF work, when an SMA connector is required. It hugs the edge of a standard 0.063" thick PCB and 'launches' off of the edge. We like these for their ease of soldering and low ...

SKU: SF-BOB-10124 | Brand: SparkFun

This is a breakout board for the SP3485 RS-485 transceiver IC, which will convert a UART serial stream to RS-485. The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can re...

SKU: AF-706 | Brand: Adafruit

These extra-long stacking headers are designed for BeagleBone Capes, allowing you to stack multiple capes on a single BeagleBone for modular, expandable designs. They work just like standard 2×23 0.1"-spaced female he...

SKU: AF-1923 | Brand: Adafruit

A 10-segment LED bar graph display in yellow-green. At just 1" (25mm) long, it's compact enough to plug directly into a breadboard while remaining clearly visible. The diffused rectangular lenses give a clean, even gl...