Components

SKU: DF-FIT0244 | Brand: DFRobot

A pack of 50 basic 3mm LEDs in five colours — 10 each of red, green, yellow, white, and blue. Handy for prototyping, indicator lights, and Arduino projects. Specifications Forward Voltage – 1.8–2.2V Max Current – ...

SKU: SF-PRT-08272 | Brand: SparkFun

This 2 mm pitch 10-pin socket mates with XBee radio modules from Digi, allowing you to mount your XBee without soldering it directly to a PCB. You'll need two of these sockets to connect to all 20 pins on an XBee modu...

SKU: SF-COM-00533 | Brand: SparkFun

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very standard red LED. The lens is 3mm in diameter, and is diffused.

SKU: SF-COM-11620 | Brand: SparkFun

A compact linear-taper slide potentiometer rated at 10 kΩ and 0.1 W. This small slider features solder tab connections, a 20 mm travel distance, and two mounting holes for easy installation. Key Features Linear Tap...

SKU: AF-161 | Brand: Adafruit

CdS cells are little light sensors. As the squiggly face is exposed to more light, the resistance goes down. When its light, the resistance is about 5-10KΩ, when dark it goes up to 200KΩ. To use, connect one side o...

SKU: DF-FIT0365 | Brand: DFRobot

 INTRODUCTION Premium quality jumper wires for prototyping. Made with 26AWG multi-strand wire and sturdy male pins. Each jumper wire is approximately 210mm in length. Each pack comes with 30 jumper wires in a...

SKU: SF-COM-11372 | Brand: SparkFun

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very basic 5mm LED with a blue lens. It has a typical forward voltage of 3.4V and ...

SKU: SF-COM-11121 | Brand: SparkFun

Check out these big 10mm through-hole LEDs! The opaque epoxy package causes these LEDs to have a soft, diffuse glow.Features: 3.0-3.4VDC Forward Voltage 20mA Forward Current 40 degree viewing angle 150-180 MCD output ...

SKU: SF-COM-12903 | Brand: SparkFun

Sometimes when you have too many choices, it’s hard to make a good decision. In fact, there are times when you just want a bag of LEDs, just one of each, that’s all you want. Well too bad, you are getting two of each!...

SKU: SF-PRT-10571 | Brand: SparkFun

These are simple 2-position screw terminals with 2.54mm pitch pins. Rated up to 150V @ 6A, this terminal can accept 30 to 18AWG wire. The 2.54mm pitch will line up with standard 0.1" perf boards.Documents: Datasheet

SKU: AF-3377 | Brand: Adafruit

Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels — they display a single colour with no digital control needed, making t...

SKU: AF-679 | Brand: Adafruit

These are very interesting 5mm diffused RGB LEDs - instead of having 4 pins to control 3 LEDs, they have only two leads - power and ground. When powered, the LEDs perform a slow fade through the rainbow, from re...

SKU: AF-756 | Brand: Adafruit

Transistors are powerful little electronic switches, and we really like these NPN transistors whenever we need to control medium-power electronics such as small motors, solenoids, or IR LEDs. We find them so handy, th...

SKU: LB-LS3779 | Brand: Little Bird

A pack of 10 general-purpose 2N2222A NPN bipolar transistors in a TO-92 package. The 2N2222A is one of the most widely used transistors in electronics, suitable for switching and signal amplification in a broad range ...

SKU: LB-LS000A | Brand: Little Bird

A pack of 30 tactile pushbutton switches in six vibrant colours — blue, white, yellow, green, black, and red. Each 12mm switch comes with a snap-on square cap, making it easy to create colour-coded controls for your p...

SKU: LB-LS6214 | Brand: Little Bird

Introducing our Tact Switch 6mm x 6mm x 5mm - 10 pack, the perfect addition to your electronic projects. These small and compact switches are designed for easy, seamless integration into your circuit boards. With a si...

SKU: LB-LS3506 | Brand: Little Bird

This 2×20 pin extra tall male GPIO header stands 12 mm high, providing additional clearance when soldering onto HATs, Bonnets, or custom boards for Raspberry Pi. It's ideal for boards that don't come with headers pre-...

SKU: AF-5666 | Brand: Adafruit

The Adafruit IoT Button with NeoPixel BFF adds a chunky 12 mm tactile button and an RGB NeoPixel to any QT Py or Xiao development board. It's a quick way to build simple IoT button projects with visual feedback — pres...

SKU: AF-5487 | Brand: Adafruit

These ultra-fine wired LEDs are designed for model-makers and crafters but they could also come in handy for folks who want to add tiny points of light to a design without needing SMT-level soldering skills. Use ...

SKU: DF-SEN0502 | Brand: DFRobot

This looks like a potentiometer, but it’s an encoder switch. It is a cascadable 360 ° rotary encoder switch with 20 pulses per revolution, and each pulse corresponds to a detent. There are LED lights set for each dete...