Components

SKU: AF-5528 | Brand: Adafruit

This Anodised Aluminium Machined Knob in silver is a premium upgrade for any rotary encoder or potentiometer. Solid machined aluminium with knurled sides for a secure grip and a shiny anodised finish that looks right ...

SKU: AF-5487 | Brand: Adafruit

These ultra-fine wired LEDs are designed for model-makers and crafters but they could also come in handy for folks who want to add tiny points of light to a design without needing SMT-level soldering skills. Use ...

SKU: DF-SEN0502 | Brand: DFRobot

This looks like a potentiometer, but it’s an encoder switch. It is a cascadable 360 ° rotary encoder switch with 20 pulses per revolution, and each pulse corresponds to a detent. There are LED lights set for each dete...

SKU: DF-TEL0142 | Brand: DFRobot

When building a project that needs to transmit some simple signals wirelessly, have you been bothered by the any of the following problems: Bluetooth's cumbersome AT command configuration and high cost, Wifi's signal ...

SKU: KI-5625 | Brand: Kitronik

The ZIP Halo is a circular LED board for the BBC micro:bit featuring 24 individually addressable full-colour ZIP LEDs (WS2812B). Each LED can display a huge spectrum of colours, enabling vibrant rainbow effects, colou...

SKU: AF-3893 | Brand: Adafruit

The JST PH 3-Pin to Male Header Cable converts a JST PH 3-pin connector into three individual colour-coded wires, each terminated with a 0.1" (2.54 mm) male header pin. It's ideal for extending sensor or LED connectio...

SKU: AF-3647 | Brand: Adafruit

Precision-machined Swiss-pin male plug headers for a tight, reliable fit. Unlike standard stamped square-pin male headers, these use machined round pins that pair exclusively with Swiss-pin female sockets — they are n...

SKU: AF-1178 | Brand: Adafruit

Rollin' rollin' rollin', you can now roll around smooth as silk with these radial bearings. Often referred to as "skate bearings" They're good for supporting a rotating rod or as a wheel hub. However, these are higher...

SKU: AF-4031 | Brand: Adafruit

Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a stereo jack so you get left and right channels as well as a ground pin. You can use any 3.5mm stereo cable with this jac...

SKU: AF-1756 | Brand: Adafruit

Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels — they display a single colour with no digital control needed, making t...

SKU: AF-1755 | Brand: Adafruit

Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels — they display a single colour with no digital control needed, making t...

SKU: AF-1663 | Brand: Adafruit

A matching pair of 3-pin JST SM connector cables — one plug and one receptacle — for creating quick-connect/disconnect points in 3-wire circuits. The locking latch keeps the connection secure while still allowing easy...

SKU: AF-2195 | Brand: Adafruit

A 10-pack of 10µF 50V electrolytic capacitors with long, flexible leads that make them easy to use on breadboards and perfboard. Each capacitor has clear labelling on the body for quick identification. Electrolytic c...

SKU: AF-2193 | Brand: Adafruit

A 10-pack of 100µF 16V electrolytic capacitors with long, flexible leads that make them easy to use on breadboards and perfboard. Each capacitor has clear labelling on the body for quick identification. Electrolytic ...

SKU: AF-2166 | Brand: Adafruit

A low-dropout (LDO) 3.3 V linear voltage regulator based on the ST L4931 in a TO-92 package. With just 0.4 V dropout, it delivers a clean, regulated 3.3 V output from input voltages as low as 3.7 V — well suited for s...

SKU: DF-FIT0121 | Brand: DFRobot

Jumper wires are one of the most important gear component for the tinkerer. Often underestimated, but one of the first things to miss. If you are starting to assemble your tinker gear and wondering if this is really n...

SKU: SF-PRT-14017 | Brand: SparkFun

This 2x20 “tall” header has the same number and spacing of pins as a Raspberry Pi and provides your board with the ability to extend the heights of your GPIO to accommodate for enclosures or other parts that can en...

SKU: AF-2914 | Brand: Adafruit

A 3.5 mm (1/8") 4-pole TRRS audio plug with screw terminal connections — no soldering required. Use stranded or solid-core wire and a small screwdriver to create custom audio cables, breakouts, and test leads. TRRS s...

SKU: SF-PRT-11895 | Brand: SparkFun

A standard 8-pin female header with 0.1" (2.54 mm) pitch, designed for through-hole mounting. Connects with most standard 8-pin male headers. Specifications Pins – 8 Pitch – 0.1" (2.54 mm) Type – Female, through-...

SKU: SF-DEV-13903 | Brand: SparkFun

This is the LilyPad Rainbow LED strip, with seven LilyPad LEDs that are still attached to one another, letting you snap LEDs apart at your leisure to sew into clothing or whatever else you can dream up.The LilyPad Rai...