Buttons & Switches

SKU: PI-COM0411 | Brand: Pimoroni

This LED tactile button combines a standard momentary push switch with a built-in red LED, all housed under a clear cap. It provides visual feedback when illuminated, making it ideal for control panels, interactive pr...

SKU: PI-COM0410 | Brand: Pimoroni

A simple LED-illuminated tactile push button with a clear cap and blue LED. It works just like a standard tactile switch but lights up when powered, giving your project visual feedback or an eye-catching indicator. K...

SKU: AF-1110 | Brand: Adafruit

The Adafruit RGB Negative 16×2 LCD + Keypad Kit is a Pi Plate that combines a 16×2 character LCD with RGB backlight and a 5-button keypad, all controlled over I2C using just two pins. The negative-style display shows ...

SKU: PR-PIM028 | Brand: Little Bird

The Touch module has four capacitive touch buttons and four bright white LEDs. It's ideal for reaction time games, a tiny piano, or a code entry keypad. Features CAP1166 driver chip Four capacitive touch...

SKU: PR-PIM034 | Brand: Little Bird

An analogue joystick module for the Pimoroni Flotilla ecosystem, featuring a two-axis thumbstick with a built-in click button. Use it as a game controller, to steer a robot, or as a general-purpose input device. Key ...

SKU: PI-COM0400 | Brand: Pimoroni

An 8-pole DIP (dual in-line package) switch with top-slide actuators for setting configuration options on PCBs. Each of the eight SPST switches operates independently, making it suitable for address selection, mode co...

SKU: AF-558 | Brand: Adafruit

These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and you can fit these in place, there's even a rubber gasket to keep wat...

SKU: AF-559 | Brand: Adafruit

A chrome-plated metal pushbutton with an illuminated red LED ring, designed for panel mounting in a 16 mm hole. The weatherproof design includes a rubber gasket to seal the enclosure against water ingress, making it s...

SKU: AF-482 | Brand: Adafruit

These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and you can fit these in place, there's even a rubber gasket to keep water ou...

SKU: KI-2709 | Brand: Kitronik

This sewable two position miniature slide switch from Kitronik allows LEDs to be turned on or off in your e-textiles projects.It has two connection points to which the conductive thread is connected. The PCBs are doub...

SKU: LB-00331 | Brand: Little Bird

A small push-button switch module on a breakout board with a built-in pull resistor, so no external resistors are needed. The 3-pin header (signal, VCC, GND) plugs directly into a solderless breadboard or connects via...

SKU: AF-1616 | Brand: Adafruit

The Adafruit Trellis is an open-source backlight keypad driver system designed to work with the Adafruit 4×4 elastomer keypad and 3mm LEDs. Each tile handles keypress detection and LED control for a 4×4 grid over I2C,...

SKU: SF-COM-08747 | Brand: SparkFun

This is a black plastic bezel, custom made to mate with the silicon rubber pads. Black 1/8" ABS plastic. Using two of these bezels with two of the top bezels will create a 4x4 bezel appropriate for the full button ...

SKU: SF-COM-08746 | Brand: SparkFun

This is a black plastic bezel, custom made to mate with the silicon rubber pads. Black 1/8" ABS plastic. We use four 4/40-0.5" size screws matched with plastic standoffs to attach the 2x2 button pad and Simon proje...

SKU: AF-173 | Brand: Adafruit

The "poor man's" accelerometer! Tilt sensors are switches that can detect basic motion/orientation. The metal tube has a little metal ball that rolls around in it, when its tilted upright, the ball rolls onto the cont...

SKU: AF-3219 | Brand: Adafruit

Fire up your engines because these are the hot-rods of toggle switches! Equipped with an aerodynamic yellow protective casing, and a yellow LED at the tip of the switch, this Yellow LED Toggle Switch is sure&nbsp...

SKU: SF-BOB-10467 | Brand: SparkFun

This simple breakout board makes it easy to use our LED tactile switches in a breadboard, or your next project. Note: Populate the board according to the polarity of the LED on the switch. The markings for the swi...

SKU: SF-COM-10443 | Brand: SparkFun

This is a simple LED-illuminated tactile button with a clear cap. It’s just like a basic tactile button, but it lights up blue! So now you can get visual feedback, or light up your project. These have a 12mm body a...

SKU: SF-COM-10442 | Brand: SparkFun

A tactile push button with a built-in red LED, combining momentary switching with visual feedback in a single component. Press the button and it lights up red — ideal for control panels, interactive projects, and anyw...

SKU: SF-COM-10440 | Brand: SparkFun

This is a simple LED-illuminated tactile button with a green cap. It’s just like a basic tactile button, but it lights up green! So now you can get visual feedback, or light up your project. These have a 12mm body and...