Brands

SKU: DF-SEN0216 | Brand: DFRobot

The Water Flow sensor measures the rate of a liquid flowing through it. The YF-S401 water flow sensor consists of a plastic valve body, flow rotor and hall effect sensor. It is usually used at the inlet end to det...

SKU: AF-828 | Brand: Adafruit

An inline flow sensor for measuring liquid or water flow in solar heating, computer cooling, irrigation, and other fluid projects. The sensor uses a pinwheel with a magnet and an external hall effect sensor to count r...

SKU: AF-3456 | Brand: Adafruit

This 5×AA battery holder delivers approximately 7.5V from five AA batteries, terminated with a 2.1mm DC barrel plug (centre positive). It provides the ideal voltage for Arduino boards and other development boards with...

SKU: SF-COM-09650 | Brand: SparkFun

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very standard green LED. The lens is 3mm in diameter, and is diffused.

SKU: AF-1955 | Brand: Adafruit

These Male/Male Jumper Wires are handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 12" (300mm) long and come in a 'strip' of 20 (2 pieces of each of ten rainbo...

SKU: AF-2000 | Brand: Adafruit

Note: The Pro Trinket's bit-bang USB technique is a legacy approach that may not work reliably with modern operating systems. For new projects, consider an ItsyBitsy or Metro Mini board with native USB support at a c...

SKU: AF-2017 | Brand: Adafruit

Add a micro-slice standard solderless breadboard to your Perma-Proto or other perf-board. This 2x4 point solder-less breadboard is a good way to add some solderless prototyping space if you just need to have...

SKU: AF-858 | Brand: Adafruit

This is a great first stepper motor, good for small projects and experimenting with steppers. This uni-polar motor has a built in mounting plate with two mounting holes. There are only 32 step (11.25 degree) per revol...

SKU: DF-DFR0460 | Brand: DFRobot

The 64×32 RGB LED Matrix Panel with 4mm pitch from DFRobot features 2048 full-colour RGB LEDs, each independently controllable. With its slim 11mm profile and durable construction, this panel is suitable for both indo...

SKU: DF-DFR0486 | Brand: DFRobot

The Gravity I²C OLED-2864 is a 0.96″ blue OLED display module driven by the SSD1306 controller. It communicates via I²C and refreshes at up to 60 Hz, making it ideal for real-time data readouts on Arduino and other mi...

SKU: AF-3531 | Brand: Adafruit

The Adafruit 128×64 OLED Bonnet is a compact display add-on for Raspberry Pi, featuring a 1.3" diagonal monochrome OLED screen with a 5-way joystick and two pushbuttons. The high-contrast white OLED pixels are individ...

SKU: DF-DFR0064 | Brand: DFRobot

The DFRobot 386AMP audio amplifier module is based on the LM386 low-voltage audio power amplifier IC. With a fixed voltage gain of 26 dB (20× amplification) and static power consumption of only 24 mW at 6V, it's well ...

SKU: SF-COM-09479 | Brand: SparkFun

The LN298 is a high voltage, high current, dual full-bridge motor driver designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC and stepping motors. Comes in a stagge...

SKU: DF-FIT0057 | Brand: DFRobot

USB 2.0 type A to mini USB 5-pin. This is a new, smaller connector for USB devices. mini USB connectors are about half the height of mini USB. mini USB is found on newer hand held devices like cell phones and port...

SKU: SF-PRT-09385 | Brand: SparkFun

A pack of 10 premium 12″ (30 cm) male-to-female jumper wires for breadboarding, prototyping, and connecting to 0.1″ pitch headers. Each wire has a male pin on one end and a female socket on the other, making them vers...

SKU: AF-3589 | Brand: Adafruit

The Adafruit PiUART is a compact add-on that provides USB serial console access and switchable power for your Raspberry Pi. It plugs directly onto the GPIO header and connects to your computer via a Micro-USB cable, g...

SKU: AF-5510 | Brand: Adafruit

nOOds are ultra-flexible LED filaments — the same type found inside decorative Edison-style LED bulbs, but available as standalone strips for your own projects. This 300 mm pink nOOd is made of dozens of parallel LED ...

SKU: SF-COM-13326 | Brand: SparkFun

Sometimes when you have too many choices, it’s hard to make a good decision. In fact, there are times when you just want a bag of LEDs, just one of each, that’s all you want. Well here you go! The LED Mixed Bag con...

SKU: SF-PRT-10588 | Brand: SparkFun

Simple breakout board for the 3.5mm audio jack. Use this breakout (shipped bare) to allow breadboard or SIP access to the super-common 3.5mm audio jack. All five pins are broken out.

SKU: PR-PIM377 | Brand: Little Bird

Grow your projects on Breakout Garden. It's the easiest way to use breakouts with your Raspberry Pi. There's no soldering required, just pop up to six Pimoroni breakouts into the slots on Breakout Garden and get st...