Brands

SKU: SF-ROB-10455 | Brand: SparkFun

The SEAFLO mini water pump is a submersible 12 V pump capable of moving up to 1325 litres per hour (350 GPH). Powered by a heavy-duty 1.5 A motor housed in a tough thermoplastic body, it handles continuous operation i...

SKU: DF-DFR0376 | Brand: DFRobot

INTRODUCTION OCELL is a 0.5" micro OLED display designed for Arduino and other microcontrollers. This micro OLED display is small as the grown-up's fingernail- 0.5" only. It has 450cd/m^2 sc...

SKU: DF-FIT0452 | Brand: DFRobot

A 2-way lever-action wire connector made from flame-retardant material. These connectors provide a quick, solderless way to join wires — simply lift the lever, insert the stripped wire, and push the lever down to lock...

SKU: DF-FIT0453 | Brand: DFRobot

A GSM antenna with SMA connector and magnetic base for easy mounting on ferrous metal surfaces. The 3 m extension cable uses 174 pure copper construction for low impedance, and the antenna provides 2.5 dBi signal gain...

SKU: SF-PRT-12790 | Brand: SparkFun

This is a 2x23 pin female PTH header, with extra long legs which makes great for stacking. This piece is in the common configuration for Beaglebone Black headers. Each pin has a spacing of 0.1" in between each othe...

SKU: SF-ROB-10391 | Brand: SparkFun

A linear push-type solenoid rated for 36 V DC that also works well at 12 V. Solenoids produce linear motion for pushing, pulling, or actuating switches and levers. This unit has a measured throw of approximately 10 mm...

SKU: SF-PRT-10375 | Brand: SparkFun

This is a simple five wire cable. Great for jumping from board to board or just about anything else. There is a 5-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway hea...

SKU: AF-3306 | Brand: Adafruit

Fire up your engines because these are the hot-rods of toggle switches! Equipped with an aerodynamic blue protective casing, and a diffused blue LED at the tip of the switch, this Blue LED Toggle Switch is s...

SKU: SF-PRT-10372 | Brand: SparkFun

This is a simple two wire cable. Great for jumping from board to board or just about anything else. There is a 2-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway headers...

SKU: AF-1827 | Brand: Adafruit

Make your own USB connections without slicing apart a USB cable and soldering those thin wires inside. This is the 'slim' version of the DIY USB-A Male connector. It's a little more elegant because instead of snapp...

SKU: DF-KIT0098 | Brand: DFRobot

INTRODUCTION Breadboard-Plugin Components Pack is a new kit designed for breadboard experiment. It provides many kinds of components, such as resistors, capacitors, diodes, transistor .et...

SKU: SF-PRT-10361 | Brand: SparkFun

This is a simple six wire cable. Great for jumping from board to board or just about anything else. These cables mate with the connectors listed below. They have bare wires on one end and a 6-pin JST SH connector on t...

SKU: SF-ROB-10335 | Brand: SparkFun

This pan/tilt bracket kit includes two brackets and all the hardware needed to build a pan/tilt mechanism using two servo motors. Perfect for mounting cameras, sensors, or other small payloads that need two-axis posit...

SKU: SF-COM-12766 | Brand: SparkFun

The L7812 is a three-terminal positive voltage regulator with a fixed 12V output. It provides stable local regulation with built-in protection against overcurrent, thermal overload, and short circuits, making it a rel...

SKU: SF-PRT-10287 | Brand: SparkFun

This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm, center-positive male barrel jack. If you need to connect bare wires to a barrel jack...

SKU: AF-1856 | Brand: Adafruit

What's better than a single LED? Lots of LEDs! Matrices like these are 'multiplexed' - so to control 64 LEDs you need 16 pins. That's a lot of pins, and there are driver chips like the MAX7219 that can control a...

SKU: SF-PRT-10255 | Brand: SparkFun

The LiPower board is based on the incredibly versatile TPS61200 boost converter. The board is configured to be used with a LiPo battery, has solder jumper selectable 5V and 3.3V output, and an under voltage protection...

SKU: SF-PRT-12711 | Brand: SparkFun

The SparkFun USB LiPoly Charger is a single-cell Li-Ion/Li-Polymer battery charging board based on the MCP73831T. It charges 3.7V LiPo cells at a selectable rate of 500 mA or 100 mA via a solder jumper, with power inp...

SKU: AF-1858 | Brand: Adafruit

This 2.2"/57mm long antenna has 2dBi of gain and 50Ω impedance so it will work fantastically with just about any 850/900/1800/1900/2100 wireless receiver/transmitter such as any Cellular or GSM/GPRS device. Anten...

SKU: AF-1897 | Brand: Adafruit

The Adafruit SPI Non-Volatile FRAM Breakout provides 64 Kbit (8 KBytes) of ferroelectric RAM (FRAM) storage over SPI. FRAM combines the non-volatile retention of flash with the instant read/write speed of SRAM — no pa...