Brands

SKU: AF-1187 | Brand: Adafruit

OMG WATCH OUT! This 100mm diameter arcade button with a 10mm deep plastic base is so massive and inviting it may collapse upon itself and form a black hole from which not even light can escape! Until it does, howe...

SKU: AF-1609 | Brand: Adafruit

The Adafruit Perma-Proto Half-Sized Breadboard PCB mirrors the layout of a standard half-size solderless breadboard, making it simple to transfer prototyped circuits to a permanent soldered board. With 30 rows of 5-ho...

SKU: AF-1713 | Brand: Adafruit

Add an ear to your project with this well-designed electret microphone amplifier with AGC. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, we use th...

SKU: AF-1463 | Brand: Adafruit

Round and round they go! 16 ultra-bright smart RGB NeoPixels are arranged in a circle with a 44.5 mm (1.75″) outer diameter. Each LED is individually addressable from a single microcontroller pin, delivering 24-bit co...

SKU: AF-2310 | Brand: Adafruit

The Adafruit Perma-Proto HAT for Pi Mini Kit is a full-sized prototyping daughter board for any Raspberry Pi with a 2×20 GPIO header (Pi Zero, A+, B+, Pi 2, 3, 4, 5). It provides a grid of 0.1″ soldering holes connect...

SKU: AF-2167 | Brand: Adafruit

Infrared (IR) break-beam sensors are a simple way to detect motion. They work by having an emitter side that sends out a beam of human-invisible IR light, then a receiver across the way which is sensitive to tha...

SKU: DF-DFR0095 | Brand: DFRobot

An infrared transmitter is simply a Light Emitting Diode which generates IR light (invisible IR light)--light with a wavelength of between 1 mm and 750 nanometers, and some associated circuitry. In an infrared ...

SKU: AF-3082 | Brand: Adafruit

A tall-profile aluminium heatsink with pre-applied thermal adhesive for easy installation on the Raspberry Pi 3 and other single board computers. The taller 15mm height provides greater surface area for improved heat ...

SKU: AF-367 | Brand: Adafruit

Little clicky switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a solderless breadboard as shown in this tutorial. The pins are normally open (disconnected) a...

SKU: AF-413 | Brand: Adafruit

Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This mak...

SKU: SF-COM-10302 | Brand: SparkFun

These tactile buttons are great for all sorts of projects. This assortment comes with 2 of each of 6 different colors for a total of 12 buttons. The colored caps are removable and the buttons fit into breadboards. ...

SKU: AF-746 | Brand: Adafruit

The Adafruit Ultimate GPS Breakout (Version 3) is a high-performance GPS module built around the MTK3339 chipset. With 66 channels, -165 dBm tracking sensitivity, and up to 10 Hz position updates, it delivers accurate...

SKU: DF-DFR0457 | Brand: DFRobot

In most Arduino projects, relays are the first choice to drive some large current device. It requires a certain amount of current to drive the internal coil to pick-up contact. But for some MCU, like Intel Edison,...

SKU: DF-FIT0080 | Brand: DFRobot

A 4-cell AA battery holder in a square (2×2) configuration with a sliding removable cover and a built-in ON/OFF switch. Features 5-inch tinned leads for easy soldering. The cover keeps batteries secure, and the switch...

SKU: AF-4714 | Brand: Adafruit

We use 2 pin JST PH connectors for all our battery packs, and if you want to put a board in series, like our LC709203F Stemma QT battery gauge, this cable will be very handy! Both ends have a JST PH 2mm pitch 2-pin...

SKU: LB-LR18 | Brand: Little Bird

Looking for a Robot Chassis?   Check out our 2 Wheel Robot Chassis in Blue.  Perfect for adding your own electronics to.  It comes with two motors which can be connected to your Arduino, Micro:Bit or...

SKU: WS-16865 | Brand: Waveshare

Note: Raspberry Pi and micro SD card are NOT included.OverviewThe GamePi20 is a mini retro video game console based on Raspberry Pi Zero / Zero W / Zero WH, recalls you all the gaming pleasures in the memory.This acce...

SKU: LB-LS7231 | Brand: Little Bird

Introducing the DIY Electromagnetic Swing Induction Kit - perfect for those who love hands-on projects and learning new skills! This kit will teach you how to solder and build your own electromagnetic swing, a fun and...

SKU: EC-SEM00006D | Brand: Elecrow

The All-in-one Starter Kit for Micro:bit is a beginner-friendly learning platform that integrates 13 sensor modules on a single circuit board — no soldering or wiring required. Simply plug in your micro:bit and start ...

SKU: SF-TOL-25571 | Brand: SparkFun

Master the art of soldering with the iFixit Soldering Splint by your side. Compact yet packed with utility, this tool is designed to seamlessly integrate into both intricate electronics soldering projects and those im...