Brands

SKU: DF-FIT0800 | Brand: DFRobot

A compact amphibious micro submersible pump perfect for building small fountains, automated plant watering systems, and DIY water projects. Powered by 3–6V DC, it features low noise operation, high efficiency, and eas...

SKU: AF-4401 | Brand: Adafruit

This 4-wire cable is a little over 200mm / 7.8" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching fe...

SKU: DF-TEL0138 | Brand: DFRobot

This is an Ublox chip-based GPS receiver module of low power and high sensitivity that can receive 56 channels satellite signal. Compared with traditional GPS receivers, it brings much more accurate and faster-positio...

SKU: DF-FIT0543 | Brand: DFRobot

A 1.5 m Mini HDMI to standard HDMI cable for connecting devices with a Mini HDMI port to monitors, TVs, and projectors. Gold-plated connectors resist oxidation for reliable, long-lasting connections, and the shielded ...

SKU: DF-DFR0564 | Brand: DFRobot

Still using a big, bulky, traditional power adapter to charge your lithium battery? DFRobot provides you with a compact and efficient 7.4V lithium battery USB charger, only the size and weight of an ordinary Gravit...

SKU: AF-3857 | Brand: Adafruit

The Feather M4 Express is built around the ATSAMD51J19, a 120 MHz Cortex M4 processor with hardware floating point and DSP instructions, 512 KB flash, and 192 KB RAM. It ships with CircuitPython pre-loaded — plug it i...

SKU: AF-1085 | Brand: Adafruit

Add precision analog-to-digital conversion to any microcontroller with the ADS1115 breakout. This 16-bit ADC delivers 860 samples per second over I2C, with four single-ended or two differential input channels and a bu...

SKU: AF-1186 | Brand: Adafruit

OMG WATCH OUT! This 100mm diameter arcade button with a 16mm deep plastic base is so massive and inviting it may collapse upon itself and form a black hole from which not even light can escape! Until it does, howev...

SKU: AF-2670 | Brand: Adafruit

Make your next project as you imagine it with prototyping perfboards that can easily be cut with scissors like these Bakelite Universal Perfboard Plates! We wanted a perfboard that was both customizable a...

SKU: SF-TOL-09317 | Brand: SparkFun

This is a solderer’s best helper, the third hand. Comes with a heavy base, two alligator clips, a soldering iron holder, and a good magnifying glass. Note that we don’t normally need a third hand. It’s nice, but so...

SKU: SF-PRT-12044 | Brand: SparkFun

This red Mini Breadboard is a great way to prototype your small projects! With 170 tie points there’s just enough room to build and test simple circuits; They’re also great for breaking out DIP package ICs to jumpe...

SKU: SF-BOB-12009 | Brand: SparkFun

The SparkFun Bi-Directional Logic Level Converter safely translates signals between different voltage levels — stepping 5V down to 3.3V and 3.3V up to 5V on the same channel. It also works with 2.8V and 1.8V devices, ...

SKU: DF-DFR0251 | Brand: DFRobot

A relay is an electrically operated switch, which has a control system (also known as the input circuit) and the controlled system (also known as the output circuit), usually used in automatic control circuit. It i...

SKU: AF-64 | Brand: Adafruit

This is a cute half size breadboard, good for small projects. It's 2.2" x 3.4" (5.5 cm x 8.5 cm) with a standard double-strip in the middle and two power rails on both sides. You can pull the power rails off easily to...

SKU: SF-DEV-11235 | Brand: SparkFun

The Arduino and Breadboard Holder is a sturdy plastic base plate that keeps your Arduino and breadboard neatly organised during prototyping. The board mounts with two included screws using the standard Arduino mountin...

SKU: SF-ROB-13259 | Brand: SparkFun

These are a pair of basic, 65mm wheels with black rubber tires. These wheels are the same ones designed to fit onto DAGUs right angle gear motors utilized in the Magician Chassis and RedBot Kit. With these wheels you ...

SKU: DF-KIT0021 | Brand: DFRobot

A waterproof DS18B20 digital temperature sensor kit with everything you need to connect to an Arduino. The stainless steel probe measures temperatures from -55°C to +125°C over a 1-Wire interface, requiring just one d...

SKU: SF-PRT-12794 | Brand: SparkFun

These are 6" long jumper wires terminated as male to female. Use these to jumper from any male or female header on any board. Multiple jumpers can be connected next to one another on a 0.1" header. Comes in one pac...

SKU: DF-SEN0189 | Brand: DFRobot

The Gravity Analog Turbidity Sensor measures water clarity by detecting the level of suspended particles. It works by measuring light transmittance and scattering rate, which change with the amount of total suspended ...

SKU: AF-815 | Brand: Adafruit

The Adafruit 16-Channel PWM/Servo Driver uses the PCA9685 chip to provide 16 channels of 12-bit PWM output over I2C. With a built-in clock, the driver runs independently — no need to continuously send signals from you...