Brands

SKU: AF-937 | Brand: Adafruit

This handy USB extension cable will make it easy for you to enclose a device that has a micro-B type port. We think this would be most handy when putting an Arduino Leonardo or Raspberry Pi in a box.The jack half h...

SKU: AF-1178 | Brand: Adafruit

Rollin' rollin' rollin', you can now roll around smooth as silk with these radial bearings. Often referred to as "skate bearings" They're good for supporting a rotating rod or as a wheel hub. However, these are higher...

SKU: AF-4031 | Brand: Adafruit

Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a stereo jack so you get left and right channels as well as a ground pin. You can use any 3.5mm stereo cable with this jac...

SKU: AF-1405 | Brand: Adafruit

Get started with the fabulous Adafruit Flora platform with this lovely budget kit, just enough to get you started with this fun wearable computer. Included are enough parts to make your first wearable electronic pr...

SKU: AF-1756 | Brand: Adafruit

Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels — they display a single colour with no digital control needed, making t...

SKU: AF-1755 | Brand: Adafruit

Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels — they display a single colour with no digital control needed, making t...

SKU: AF-1663 | Brand: Adafruit

A matching pair of 3-pin JST SM connector cables — one plug and one receptacle — for creating quick-connect/disconnect points in 3-wire circuits. The locking latch keeps the connection secure while still allowing easy...

SKU: AF-2166 | Brand: Adafruit

A low-dropout (LDO) 3.3 V linear voltage regulator based on the ST L4931 in a TO-92 package. With just 0.4 V dropout, it delivers a clean, regulated 3.3 V output from input voltages as low as 3.7 V — well suited for s...

SKU: AF-2430 | Brand: Adafruit

Pogo pins are little spring-loaded contacts, very handy for making jigs, or making momentary (but electrically solid) contacts. We use them by the dozen for making programming and testing jigs but they're handy also i...

SKU: DF-FIT0085 | Brand: DFRobot

This custom-designed plastic wheel has a rubber tire measuring 1.65" (42 mm) in diameter and is designed to fit the output shafts on our mini metal gearmotors as well as the Solarbotics metal gear motors. Teeth on...

SKU: DF-SEN0032 | Brand: DFRobot

Breakout board for the Analog Device ADXL345. The ADXL345 is a small, thin, low power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g. Digital output data is formatted as 16-bit twos ...

SKU: DF-FIT0121 | Brand: DFRobot

Jumper wires are one of the most important gear component for the tinkerer. Often underestimated, but one of the first things to miss. If you are starting to assemble your tinker gear and wondering if this is really n...

SKU: DF-SEN0129 | Brand: DFRobot

INTRODUCTION This is an Arduino CH4 gas sensor. It uses MQ4 probe which is able to detect nature gas, CH4. It is less sensitivity in detecting alcohol, cooking fumes, and cigarette smok...

SKU: DF-FIT0190 | Brand: DFRobot

A 500-piece assortment of 0805 SMD resistors covering 25 common values from 620 Ω to 12 kΩ. Each value comes as a strip of 20 resistors, making it easy to keep your stock organised and identify values quickly. The 080...

SKU: AF-2927 | Brand: Adafruit

A Feather board without ambition is a Feather board without FeatherWings! This is the DC Motor + Stepper FeatherWing which will let you use 2 x bi-polar stepper motors or 4 x brushed DC motors (or 1 ...

SKU: SF-PRT-14017 | Brand: SparkFun

This 2x20 “tall” header has the same number and spacing of pins as a Raspberry Pi and provides your board with the ability to extend the heights of your GPIO to accommodate for enclosures or other parts that can en...

SKU: AF-2914 | Brand: Adafruit

A 3.5 mm (1/8") 4-pole TRRS audio plug with screw terminal connections — no soldering required. Use stranded or solid-core wire and a small screwdriver to create custom audio cables, breakouts, and test leads. TRRS s...

SKU: SF-PRT-11895 | Brand: SparkFun

A standard 8-pin female header with 0.1" (2.54 mm) pitch, designed for through-hole mounting. Connects with most standard 8-pin male headers. Specifications Pins – 8 Pitch – 0.1" (2.54 mm) Type – Female, through-...

SKU: SF-DEV-13903 | Brand: SparkFun

This is the LilyPad Rainbow LED strip, with seven LilyPad LEDs that are still attached to one another, letting you snap LEDs apart at your leisure to sew into clothing or whatever else you can dream up.The LilyPad Rai...

SKU: SF-CAB-00509 | Brand: SparkFun

A pair of banana plug to alligator clip cables in red and black, ideal for connecting multimeters, power supplies, oscilloscopes, and function generators to your circuit or test points. Specifications Connector A –...