Brands and Manufacturers

SKU: AF-4730 | Brand: Adafruit

This stuff is called "wire-wrap wire" because it used to be used for wire-wrapping high-speed digital circuits on a special kind of contact board. It's pretty rare to see wire-wrapping in these days of low-cost PCB fa...

SKU: DF-SEN0169-V2 | Brand: DFRobot

DFRobot Gravity: Analog pH meter pro V2 is specifically designed to measure the pH of the solution and reflect the acidity or alkalinity. It is commonly used in various applications such as aquaponics, aquaculture, an...

SKU: EC-ACS95915S | Brand: Elecrow

The Elecrow Lora Shield is a long range transceiver on a Arduino shield form factor and based on Open source library.The Lora Shield allows the user to send data and reach extremely long ranges at low data-rates.It...

SKU: EC-RPA01416L | Brand: Elecrow

This RGB LED HAT adds a 4×8 matrix of individually addressable RGB LEDs to your Raspberry Pi. With 256 brightness levels and 24-bit colour depth (over 16.7 million colours), it's perfect for creating colourful display...

SKU: EC-CEF02096C | Brand: Elecrow

If you want to connect Raspberry Pi which has only one single micro port to various USB, the USB Hub for Raspberry Pi Zero is your right choice. Especially there is no soldering and wires reqiured. The USB Hub for RPI...

SKU: EF-EF04094 | Brand: ElecFreaks

The Octopus Water Level Sensor detects water level using exposed parallel traces on the PCB. As the water level rises, more traces are submerged, producing a higher analogue signal output. Compatible with micro:bit (3...

SKU: EF-EF02053 | Brand: ElecFreaks

Basic:bit is a basic breakout board of micro:bit. It carries a buzzer and three groups of GVS pins(P0/P1/P2) on board. Each group of GVS pins separately leads out the IO port, 3V port and GND port on micro:bit. Small ...

SKU: EF-EF03405 | Brand: ElecFreaks

The Octopus:bit is a breakout board for the BBC micro:bit that extends all GPIO ports (P0–P16, P19–P20) into colour-coded pin headers with VCC and GND alongside each I/O pin. This makes connecting sensors, servos, and...

SKU: DF-SEN0311 | Brand: DFRobot

A commercial-grade waterproof ultrasonic distance sensor with UART serial output. The A02YYUW features a much smaller blind zone (3 cm) and wider sensing angle than many comparable sensors, plus penetration through sm...

SKU: SF-CAB-15455 | Brand: SparkFun

This panel mount USB-C extension cable enables you to more easily enclose a project that contains a USB-C port. The cable is 6" in length and includes two 14mm M3 screws compatible with the cable's 3mm panel mount hol...

SKU: SF-SEN-14727 | Brand: SparkFun

This miniature straight bar load cell (sometimes called a strain gauge) can translate up to 100g of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that cha...

SKU: AF-2784 | Brand: Adafruit

ΩMG! You're not going to be able to resist these handy resistor packs! Well, axially, they do all of the resisting for you! This is a 25 Pack of 10K Ω Resistors. More specifically, they are carbon film, ...

SKU: AF-2781 | Brand: Adafruit

ΩMG! You're not going to be able to resist these handy resistor packs! Well, axially, they do all of the resisting for you! This is a 25 Pack of 470Ω Resistors. More specifically, they are carbon film, t...

SKU: AF-3950 | Brand: Adafruit

This cable will let you turn a JST PH 4-pin cable port into 3 individual wires with high-quality 0.1" female sockets on the end. We're carrying these to match up with any of our boards with 'STEMMA' connectors o...

SKU: LB-LR0293-3 | Brand: Little Bird

An 80 cm USB-A to Micro USB cable for data transfer and charging. Compatible with development boards such as the Arduino Leonardo, as well as Raspberry Pi, mobile devices, and other electronics that use a Micro USB co...

SKU: SF-WRL-14875 | Brand: SparkFun

A compact 1/4-wave rubber duck antenna for LoRa and other 860–960MHz communication. With a centre frequency of 915MHz and 2dBi gain, this 110mm antenna is ideal for space-constrained LoRa nodes where a smaller antenna...

SKU: AF-4130 | Brand: Adafruit

This RJ-45 round panel mount adapter provides an Ethernet pass-through connection that installs in a standard round drill hole — no rectangular cutouts or filing required. Drill a ~30 mm hole in wood, plastic, or meta...

SKU: PI-COM0404 | Brand: Pimoroni

A colourful 30 mm arcade-style pushbutton in blue. With a satisfying 2 mm travel and tactile click, these buttons are ideal for arcade builds, control panels, and interactive projects. Key Features Arcade Style – C...

SKU: AF-3859 | Brand: Adafruit

A 4×AA battery holder with premium jumper header wires that plug directly into a breadboard. No stripping or soldering required — just insert the header pins into your breadboard rails and start prototyping with porta...

SKU: LB-LS0657 | Brand: Little Bird

A high-fidelity DAC expansion board for Raspberry Pi that delivers superior audio quality over the Pi's built-in 3.5mm output. Built around Texas Instruments' PCM5122 DAC chip, this board connects via the I2S interfac...