Brands and Manufacturers

SKU: AF-4730 | Brand: Adafruit

This stuff is called "wire-wrap wire" because it used to be used for wire-wrapping high-speed digital circuits on a special kind of contact board. It's pretty rare to see wire-wrapping in these days of low-cost PCB fa...

SKU: DF-SEN0169-V2 | Brand: DFRobot

DFRobot Gravity: Analog pH meter pro V2 is specifically designed to measure the pH of the solution and reflect the acidity or alkalinity. It is commonly used in various applications such as aquaponics, aquaculture, an...

SKU: EC-ACS95915S | Brand: Elecrow

The Elecrow Lora Shield is a long range transceiver on a Arduino shield form factor and based on Open source library.The Lora Shield allows the user to send data and reach extremely long ranges at low data-rates.It...

SKU: DF-DFR0626 | Brand: DFRobot

This is an IO expansion module that based on the chip MCP23017. The module can expand additional 16 IOs. It can set 8 IIC addresses, which means with this module, the microcontroller can connect 8 modules, and expand ...

SKU: EC-RPA01416L | Brand: Elecrow

This RGB LED HAT adds a 4×8 matrix of individually addressable RGB LEDs to your Raspberry Pi. With 256 brightness levels and 24-bit colour depth (over 16.7 million colours), it's perfect for creating colourful display...

SKU: EC-CEF02096C | Brand: Elecrow

If you want to connect Raspberry Pi which has only one single micro port to various USB, the USB Hub for Raspberry Pi Zero is your right choice. Especially there is no soldering and wires reqiured. The USB Hub for RPI...

SKU: EF-EF04094 | Brand: ElecFreaks

The Octopus Water Level Sensor detects water level using exposed parallel traces on the PCB. As the water level rises, more traces are submerged, producing a higher analogue signal output. Compatible with micro:bit (3...

SKU: EF-EF02053 | Brand: ElecFreaks

Basic:bit is a basic breakout board of micro:bit. It carries a buzzer and three groups of GVS pins(P0/P1/P2) on board. Each group of GVS pins separately leads out the IO port, 3V port and GND port on micro:bit. Small ...

SKU: EF-EF03405 | Brand: ElecFreaks

The Octopus:bit is a breakout board for the BBC micro:bit that extends all GPIO ports (P0–P16, P19–P20) into colour-coded pin headers with VCC and GND alongside each I/O pin. This makes connecting sensors, servos, and...

SKU: DF-SEN0311 | Brand: DFRobot

A commercial-grade waterproof ultrasonic distance sensor with UART serial output. The A02YYUW features a much smaller blind zone (3 cm) and wider sensing angle than many comparable sensors, plus penetration through sm...

SKU: SF-CAB-15455 | Brand: SparkFun

This panel mount USB-C extension cable enables you to more easily enclose a project that contains a USB-C port. The cable is 6" in length and includes two 14mm M3 screws compatible with the cable's 3mm panel mount hol...

SKU: SF-SEN-14727 | Brand: SparkFun

This miniature straight bar load cell (sometimes called a strain gauge) can translate up to 100g of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that cha...

SKU: AF-2784 | Brand: Adafruit

ΩMG! You're not going to be able to resist these handy resistor packs! Well, axially, they do all of the resisting for you! This is a 25 Pack of 10K Ω Resistors. More specifically, they are carbon film, ...

SKU: AF-2781 | Brand: Adafruit

ΩMG! You're not going to be able to resist these handy resistor packs! Well, axially, they do all of the resisting for you! This is a 25 Pack of 470Ω Resistors. More specifically, they are carbon film, t...

SKU: SF-WRL-14875 | Brand: SparkFun

A compact 1/4-wave rubber duck antenna for LoRa and other 860–960MHz communication. With a centre frequency of 915MHz and 2dBi gain, this 110mm antenna is ideal for space-constrained LoRa nodes where a smaller antenna...

SKU: AF-4130 | Brand: Adafruit

This RJ-45 round panel mount adapter provides an Ethernet pass-through connection that installs in a standard round drill hole — no rectangular cutouts or filing required. Drill a ~30 mm hole in wood, plastic, or meta...

SKU: AF-1260 | Brand: Adafruit

What's a wearable project without LEDs? Our favorite part of the Flora platform is these tiny smart pixels. Designed specifically for wearables, these updated Flora NeoPixels have ultra-cool technology: these ul...

SKU: PI-COM0404 | Brand: Pimoroni

A colourful 30 mm arcade-style pushbutton in blue. With a satisfying 2 mm travel and tactile click, these buttons are ideal for arcade builds, control panels, and interactive projects. Key Features Arcade Style – C...

SKU: AF-3859 | Brand: Adafruit

A 4×AA battery holder with premium jumper header wires that plug directly into a breadboard. No stripping or soldering required — just insert the header pins into your breadboard rails and start prototyping with porta...

SKU: AF-3923 | Brand: Adafruit

Hear the good news! This wee speaker is a great addition to any audio project where you need 8 ohm impedance and 1W or less of power. We particularly like this speaker as it is small and comes with nice skinny wires w...