Brands and Manufacturers

SKU: SF-PRT-10255 | Brand: SparkFun

The LiPower board is based on the incredibly versatile TPS61200 boost converter. The board is configured to be used with a LiPo battery, has solder jumper selectable 5V and 3.3V output, and an under voltage protection...

SKU: SF-PRT-12711 | Brand: SparkFun

The SparkFun USB LiPoly Charger is a single-cell Li-Ion/Li-Polymer battery charging board based on the MCP73831T. It charges 3.7V LiPo cells at a selectable rate of 500 mA or 100 mA via a solder jumper, with power inp...

SKU: AF-1858 | Brand: Adafruit

This 2.2"/57mm long antenna has 2dBi of gain and 50Ω impedance so it will work fantastically with just about any 850/900/1800/1900/2100 wireless receiver/transmitter such as any Cellular or GSM/GPRS device. Anten...

SKU: AF-1897 | Brand: Adafruit

The Adafruit SPI Non-Volatile FRAM Breakout provides 64 Kbit (8 KBytes) of ferroelectric RAM (FRAM) storage over SPI. FRAM combines the non-volatile retention of flash with the instant read/write speed of SRAM — no pa...

SKU: SF-PRT-10217 | Brand: SparkFun

If you need to charge LiPo batteries, this simple charger will do just that, and do it fast! The SparkFun LiPo Charger Basic is stripped down of all features and just does one thing well - charge 3.7V LiPo cells ...

SKU: DF-FIT0467 | Brand: DFRobot

INTRODUCTION This motor has a long (0.365"/9.27 mm) D profile metal output shaft that matches the 42x19mm and 32x7mm dimensions of the Pololu wheel. The brass faceplate has two mounting h...

SKU: AF-1903 | Brand: Adafruit

The PowerBoost 500 Basic is a compact DC/DC boost converter that takes input from 1.8V or higher and outputs a steady 5.2V — perfect for powering portable 5V projects from batteries. The slightly elevated 5.2V output ...

SKU: SF-PRT-12699 | Brand: SparkFun

This is the Large SparkFun Solder-able Breadboard. A bare PCB that is the exact size as our full-size breadboard with the same connections to pins and power rails. This board is especially useful for preserving a prot...

SKU: DF-DFR0411 | Brand: DFRobot

INTRODUCTION This DC motor has an integrated transistor built in to the board, eliminating the need for a motor driver. Use PWM to control it for all your DIY project needs. It uses the 3 pi...

SKU: AF-3428 | Brand: Adafruit

A voltage detector is handy for projects where you want to make sure your microcontroller doesn't run at a low voltage. For example, say you have a Feather Huzzah running on a lipoly battery every few minutes. Even...

SKU: SF-CAB-10177 | Brand: SparkFun

You might have seen these cables used in computers. They are typically used to bring USB connections from a motherboard to the external case, or the rear expansion slots. They have a 0.1" spaced 4-pin header on one en...

SKU: AF-1901 | Brand: Adafruit

A Qi-compatible wireless charging receiver module that outputs regulated 5 V at up to 500 mA. Place this module on any standard Qi charging base to receive power wirelessly — ideal for adding wireless recharging capab...

SKU: SF-SEN-12642 | Brand: SparkFun

The SparkFun Sound Detector is a small and very easy to use audio sensing board with three different outputs. The Sound Detector not only provides an audio output, but also a binary indication of the presence of so...

SKU: SF-SEN-10127 | Brand: SparkFun

This is a basic RFID tag that functions within the MIFARE Classic® 1K guidelines. You can use these for all sorts of identification and sensing applications. The tag also has 1K of data storage which can be read and w...

SKU: AF-705 | Brand: Adafruit

A compact 3-wire voltage meter with a vivid green 3-digit 7-segment display. Reads 0–99.9VDC with 0.1V precision, making it perfect for monitoring battery levels, power supplies, and electronic projects. Mounting tabs...

SKU: SF-BOB-10124 | Brand: SparkFun

This is a breakout board for the SP3485 RS-485 transceiver IC, which will convert a UART serial stream to RS-485. The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can re...

SKU: AF-706 | Brand: Adafruit

These extra-long stacking headers are designed for BeagleBone Capes, allowing you to stack multiple capes on a single BeagleBone for modular, expandable designs. They work just like standard 2×23 0.1"-spaced female he...

SKU: AF-3436 | Brand: Adafruit

The Adafruit Music Maker FeatherWing with Amplifier brings powerful audio playback to any Feather board. Built around the VS1053B codec chip, it decodes a wide variety of formats including MP3, AAC, Ogg Vorbis, WMA, M...

SKU: SF-CAB-10087 | Brand: SparkFun

The OBD-II to DB9 Cable connects your vehicle's OBD-II diagnostic port to a DB9 female serial connector, providing access to automotive bus protocols for diagnostics, data logging, and vehicle hacking projects. The c...

SKU: DF-KIT0111 | Brand: DFRobot

The Gravity Starter Kit for Arduino is a plug-and-play electronics toolkit designed for beginners and makers getting started with the Arduino platform. It includes a DFRduino UNO R3 microcontroller (fully compatible w...