Brands and Manufacturers

SKU: AF-3118 | Brand: Adafruit

Make your own custom HDMI cable or HDMI interface with ease, using this HDMI Terminal Block Breakout. You get a nice solid PCB with an HDMI plug and two strips of terminal blocks that you can use with stranded or s...

SKU: AF-3318 | Brand: Adafruit

Check out this handy USB extension cable, which will make it easy for you to enclose a device that has a Mini-B USB type port. We think this would be most handy when putting a Teensy, FTDI friend, USB LiPo charger, Be...

SKU: AF-616 | Brand: Adafruit

Give yourself some more room with an EL wire cable extender. This cable has a 2-pin JST SM plug on one end and receptacle on the other. Use it to extend the reach of EL wire, panel, tape, etc. The cable is a meter ...

SKU: AF-824 | Brand: Adafruit

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 12" (300mm) long and come in a 'strip' of 40 (4 pieces of each of ten rainbow colors). They have 0.1" male he...

SKU: AF-1949 | Brand: Adafruit

These Female/Female Jumper Wires are handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 12" (300mm) long and come in a 'strip' of 20 (2 pieces of each of ten rainb...

SKU: AF-825 | Brand: Adafruit

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are approximately 3" (75mm) long and come in a 'strip' of 40 (4 pieces of each of ten rainbow colors). They have 0.1...

SKU: AF-6070 | Brand: Adafruit

If you need to add a panel-mount connection that extends a micro SD card, this Round Panel Mount MicroSD Adapter Plug is the easiest and fastest way to panel-ify your project. The adapter is about 30mm in diameter, so...

SKU: AF-5391 | Brand: Adafruit

If you're messing around with floppy drives, or disk drives, or other devices that are usually powered with a PC motherboard you'll often see these big 'Molex' connectors used to provide power. They are used to give 5...

SKU: AF-4482 | Brand: Adafruit

These premium male-male jumper wires are handy for making wire harnesses or jumpering between headers on PCBs. They're 200mm (~7.8") long and come loose as a pack of 40 (10 pieces of red, blue, yellow, and Adafruit bl...

SKU: AF-4364 | Brand: Adafruit

Just about all electronics use a UART serial port with RX and TX pins for debugging, bootloading, programming, serial output, etc. But it's rare for a computer to have a serial port anymore. Thus, a serial cable is an...

SKU: AF-4150 | Brand: Adafruit

In this world nothing can be said to be certain, except we need headers, headers, and more headers!Each pack contains ten blue 36-pin 0.1" pitch break-away male headers.  These are a little extra special in that ...

SKU: AF-3663 | Brand: Adafruit

If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers from Pimoroni might be just what you need.  Absolutely no soldering required! All t...

SKU: AF-2104 | Brand: Adafruit

This 2x8 (16 pin - 0.1" spaced) IDC Breadboard Helper is great in conjunction with any 16-pin IDC cables. It comes in two parts, a 'pin-through' socket and a male header. The socket straddles...

SKU: AF-2101 | Brand: Adafruit

The "poor woman's" Raspberry Pi cobbler! This combo of 2x13 pin (0.1 spaced) header and socket is for our popular GPIO Ribbon Cable for Raspberry Pi Model A and B.  It comes in two parts, a 'pin-through' socke...

SKU: AF-2789 | Brand: Adafruit

The premise of this MicroUSB to 5.5/2.1mm DC Barrel Jack Adapter is simple. There's a MicroUSB plug on one end and a 5.5mm/2.1mm DC barrel jack with center positive polarity on the other. This allows you ...

SKU: AF-248 | Brand: Adafruit

A 6×AA battery holder with a 5.5mm/2.1mm DC barrel plug, ready to power Arduino boards and other electronics with a standard DC jack. Use alkaline AAs for approximately 9V at 3000–4000mAh, or rechargeable NiMH cells f...

SKU: AF-3310 | Brand: Adafruit

A 5.5×2.1mm DC barrel connector plug for adding a standard power connector to the end of your own wires. The outer shell unscrews to reveal solder terminals and a crimp strain relief, making it easy to wire up custom ...

SKU: AF-1858 | Brand: Adafruit

This 2.2"/57mm long antenna has 2dBi of gain and 50Ω impedance so it will work fantastically with just about any 850/900/1800/1900/2100 wireless receiver/transmitter such as any Cellular or GSM/GPRS device. Anten...

SKU: AF-5037 | Brand: Adafruit

This cable will make it super easy to use our plug-and-play STEMMA QT boards and controllers with chips, breakouts, and other devices that are I2C compatible but don't come with a STEMMA QT socket already on 'em.On on...

SKU: AF-1773 | Brand: Adafruit

This 50-pin top-contact FPC connector is a surface-mount component for connecting 0.5mm pitch FPC/FFC cables to your custom PCB. It's compatible with many 50-pin displays including 2.8″ TFT panels with resistive touch...