Brands and Manufacturers

SKU: DF-DFR0052 | Brand: DFRobot

The DFRobot Vibration Sensor buffers a piezoelectric transducer that responds to strain changes by generating a measurable output voltage change which is propotional with the strength of vibration.So you can know the...

SKU: AF-165 | Brand: Adafruit

The TMP36 is a low-power analog temperature sensor that outputs a voltage proportional to ambient temperature. It operates on 2.7–5.5V and requires no external calibration — simply read the analog voltage and convert ...

SKU: DF-SEN0206 | Brand: DFRobot

INTRODUCTION We can divide temperature measurement in to two types: contact and non-contact. Contact measurement can only accurately measure temperature when the testing object and the se...

SKU: AF-3333 | Brand: Adafruit

The Circuit Playground Express is an all-in-one development board packed with sensors, LEDs, and a speaker — all on a round, beginner-friendly PCB with alligator-clip pads. No soldering required. It supports four prog...

SKU: DF-DFR0971 | Brand: DFRobot

This 2-Channel I2C DAC module can output a voltage of 0-10V, which is a standard driver in industrial applications. It can be widely used with most 0-10V devices on markets such as light controllers, inverters, valves...

SKU: AF-5463 | Brand: Adafruit

This rubber sheet is made of the same carbon-black impregnated rubber material that our conductive rubber cord uses. Traditionally it would be used for EMF shielding, or conductive gaskets - but it's very fun to play ...

SKU: SF-BOB-16446 | Brand: SparkFun

The SparkFun Qwiic micro:bit Breakout is a board that connects to the BBC micro:bit and expands the capabilities of the development platform by providing access to more pins and allowing for connections to the I2C and...

SKU: SF-SEN-14727 | Brand: SparkFun

This miniature straight bar load cell (sometimes called a strain gauge) can translate up to 100g of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that cha...

SKU: AF-3923 | Brand: Adafruit

Hear the good news! This wee speaker is a great addition to any audio project where you need 8 ohm impedance and 1W or less of power. We particularly like this speaker as it is small and comes with nice skinny wires w...

SKU: AF-3692 | Brand: Adafruit

What is this TRS bit? Turtle Rock Studios? Transmission Raman Spectroscopy? Not quite, more like Tip-Ring-Sleeve. This nifty, gold-plated connector is known by many names, phone plug, phone jack, headphone j...

SKU: AF-2796 | Brand: Adafruit

The Feather M0 Adalogger is an all-in-one datalogger built around the ATSAMD21G18 ARM Cortex M0 processor, with a built-in MicroSD card holder, native USB, and LiPo battery charging. With 256KB of flash and 32KB of RA...

SKU: SF-SEN-09375 | Brand: SparkFun

This is a force sensitive resistor with a round, 0.5" diameter, sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the ...

SKU: AF-5791 | Brand: Adafruit

The Adafruit STEMMA Piezo Driver Amp uses the PAM8904 switched-capacitor driver to amplify signals for piezo elements at up to 300 kHz. With bridge-tied load (BTL) output and up to 3× voltage multiplication, it can de...

SKU: DF-DFR0762 | Brand: DFRobot

Specially designed for FireBeetle 2 series (M0, ESP32-E), this Gravity IO expansion shield offers various ports including digital, analog, I2C, UART, SPI, etc. Also, it comes with power input socket for connecting ext...

SKU: AF-4470 | Brand: Adafruit

The Adafruit MCP4728 Quad DAC with EEPROM provides four independent 12-bit digital-to-analogue converters in a single I2C package. Set precise output voltages for your project, and save your settings to the built-in E...

SKU: SF-SEN-09088 | Brand: SparkFun

This is a very small light sensor. A photocell changes (also called a photodetector, photo resistor, CdS or photoconductive cell) resistance depending on the amount of light it is exposed to. These little sensors make...

SKU: AF-161 | Brand: Adafruit

CdS cells are little light sensors. As the squiggly face is exposed to more light, the resistance goes down. When its light, the resistance is about 5-10KΩ, when dark it goes up to 200KΩ. To use, connect one side o...

SKU: AF-3377 | Brand: Adafruit

Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels — they display a single colour with no digital control needed, making t...

SKU: EF-EF04093 | Brand: ElecFreaks

Octopus Analog UV sensor (GUVA-S12SD) is the UV electric brick in our Octopus series, the basic design is from the Octopus electric bricks and the setting of its outlook, the PCB fixing hole and the connectors are the...

SKU: AF-3893 | Brand: Adafruit

The JST PH 3-Pin to Male Header Cable converts a JST PH 3-pin connector into three individual colour-coded wires, each terminated with a 0.1" (2.54 mm) male header pin. It's ideal for extending sensor or LED connectio...