Brands and Manufacturers

SKU: AF-1606 | Brand: Adafruit

The Adafruit Perma-Proto Full-Sized Breadboard PCB mirrors the layout of a standard full-size solderless breadboard, making it simple to transfer prototyped circuits to a permanent soldered board. With 60 rows of 5-ho...

SKU: PJ-PROP_SHIELD_LC | Brand: Little Bird

This low-cost Prop Shield is meant for making light and sound effects on small handheld props and wearable costumes. Audio Amplifier - Clear quality audio output to a small speaker. Fast LED Driver - Drive APA102 / ...

SKU: MD-20001 | Brand: Makedo

Looking for something for the little engineer in your life? The Makedo Scru Add-On pack is a perfect complement to the Makedo Toolkit – a great introduction to the land of Makedo. Ente...

SKU: SS-106990021 | Brand: Seeed Studio

The 5V/3.3V Breadboard Power Supply plugs directly into a standard breadboard and provides regulated 5V or 3.3V power to both rails. It accepts power via either a 7–15V DC barrel jack or a 5V Micro-USB input, giving y...

SKU: AF-1850 | Brand: Adafruit

Add a touch of sparkle to your wearables with the Adafruit Gemma Sequin Starter Pack. This beginner-friendly kit includes a GEMMA V2 sewable microcontroller, warm white LED sequins, conductive thread, needles, and a c...

SKU: AF-2158 | Brand: Adafruit

Display, elegantly, 012345678 or 9! Gaze, hypnotized, at ABCDEFGHIJKLM - well it can display the whole alphabet. You get the point. This is a nice, bright alphanumeric display that shows letters and numbers in a be...

SKU: AF-2029 | Brand: Adafruit

The Raspberry Pi B+/Pi 2/ Pi 3 has landed on the Maker World like a 40-GPIO pinned, quad-USB ported, credit card sized bomb of DIY joy. And while you can use most of our great Model B accessories by hooking up our ...

SKU: AF-2210 | Brand: Adafruit

The Adafruit Audio FX Sound Board with 2×2W Amp is a standalone audio trigger with a built-in stereo Class D amplifier — no Arduino or programming required. Simply drag and drop WAV or OGG sound files over USB, wire u...

SKU: AF-2340 | Brand: Adafruit

The Adafruit Capacitive Touch HAT adds 12 capacitive touch sensors to your Raspberry Pi using the MPR121 touch controller over I2C. Each sensor has a figure-8 hole designed for alligator clip connections — attach clip...

SKU: AF-2471 | Brand: Adafruit

The Adafruit HUZZAH ESP8266 Breakout is a breadboard-friendly WiFi microcontroller board built around the Espressif ESP8266. With an 80 MHz processor, full WiFi client and access point support, a built-in TCP/IP stack...

SKU: DF-FIT0030 | Brand: DFRobot

These 23 cm (9″) female-to-female jumper wires are a prototyping essential. Use them to connect between male headers on Arduino boards, IO shields, sensors, and breadboards. Multiple wires sit neatly side by side on s...

SKU: DF-FIT0100 | Brand: DFRobot

A pack of 10 right-angle male header strips, each with 40 breakable pins at 2.54mm pitch. The 90° bend allows horizontal connections from vertically mounted PCBs, ideal for compact enclosures and edge-mounted connecto...

SKU: AF-1500 | Brand: Adafruit

The Adafruit Trinket 3V3 is a tiny microcontroller board built around the Atmel ATtiny85 processor. At just 27mm × 15mm, it's small enough to fit into virtually any project and affordable enough to dedicate to a singl...

SKU: DF-FIT0105 | Brand: DFRobot

A pack of 10 long straight male header strips, each with 40 breakable pins at 2.54mm pitch. The extended 10mm pin length allows socket-to-socket connections, and the plastic separator can be repositioned along the pin...

SKU: DF-DFR0116 | Brand: DFRobot

This is a USB AVR programmer supported by offical Arduino IDE. Once the Arduino has lost its bootloader for some reasons, use this programmer to reburn the bootloader and save the dead Arduino. This programmer works ...

SKU: PL-2485 | Brand: Pololu

The Pololu Basic 2-Channel SPDT Relay Carrier provides simple, independent control of two single-pole, double-throw (SPDT) relay switches from low-voltage, low-current control signals. This assembled version comes rea...

SKU: DF-FIT0150 | Brand: DFRobot

This product includes 4-pin 2.0mm(0.08") mating connector housing(10 units) and crimp pins (40 units). They work with wires ranging from 28 to 26 AWG. SPECIFICATIONS 4-pin 2.0mm mating connector housing 28 to 26 A...

SKU: SF-DEV-14346 | Brand: SparkFun

The LilyPad ProtoSnap Plus is a sewable electronics prototyping board that you can use to explore circuits and programming, then break apart to make an interactive fabric or wearable project. Programming the ProtoSnap...

SKU: AF-2690 | Brand: Adafruit

This USB In-Line Voltage and Current Meter with OLED Display is a lot like the Charger Doctor we carry - if the doctor was a talented surgeon who just lost her medical license and has nothing to lose...

SKU: SF-COM-09339 | Brand: SparkFun

This 35mm concave momentary push button delivers the satisfying tactile click of an arcade button. The screw-in design makes it easy to mount in panels and enclosures, and the included 3-terminal microswitch is rated ...