Brands and Manufacturers

SKU: DF-FIT0414 | Brand: DFRobot

This is a handy cables kit for WTRnode users. It contains a USB to TTL cable which allows for a simple way to connect TTL interface devices to USB, and a WRTnode dedicated network cable. WRTnode(A Mini Op...

SKU: AF-2590 | Brand: Adafruit

The Adafruit Metro Mini 328 packs the same ATmega328P power as a full-sized Metro into a tiny breadboard-friendly form factor. Running at 16 MHz with 5V logic, it's pin-compatible with Arduino UNO R3 and works with th...

SKU: SF-DEV-10587 | Brand: SparkFun

Do you ever wish your Arduino was more musically talented? Or maybe your project could use some cool sound effects. The SparkFun Musical Instrument Shield is an easy way to add great sounding MIDI sound to your next A...

SKU: AF-3318 | Brand: Adafruit

Check out this handy USB extension cable, which will make it easy for you to enclose a device that has a Mini-B USB type port. We think this would be most handy when putting a Teensy, FTDI friend, USB LiPo charger, Be...

SKU: SF-DEV-10524 | Brand: SparkFun

The name says it all on this one. An ATmega328 in DIP package, pre-loaded with the Arduino Optiboot (Uno 16MHz) Bootloader. This will allow you to use Arduino code in your custom embedded project without having to ...

SKU: AF-2926 | Brand: Adafruit

The Terminal Block Breakout FeatherWing kit is like the Golden Eagle of prototyping FeatherWings (eg. majestic, powerful, good-looking). To start, you get a nice prototyping area underneath your Feather, wi...

SKU: SF-PRT-10371 | Brand: SparkFun

This is a simple six wire cable. Great for jumping from board to board or just about anything else. There is a 6-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway headers...

SKU: AF-616 | Brand: Adafruit

Give yourself some more room with an EL wire cable extender. This cable has a 2-pin JST SM plug on one end and receptacle on the other. Use it to extend the reach of EL wire, panel, tape, etc. The cable is a meter ...

SKU: DF-DFR0419 | Brand: DFRobot

You are viewing a 4GB RAM LattePanda with 64GB internal memory. It does not include a Windows 10 activation key. A LattePanda is a complete Windows 10 single board computer. It has everything a regular PC has a...

SKU: SF-COM-10001 | Brand: SparkFun

Knobs are a great way to finish off your project and make it easier to adjust the level of your death ray. This knob mates to a 0.25" shaft. The knob slides onto the potentiometer and holds tightly with a strong frict...

SKU: SF-SEN-09836 | Brand: SparkFun

This new version adds 2 standoff holes as well as an extra decoupling capacitor. The ADXL345 is a small, thin, low power, 3-axis MEMS accelerometer with high resolution (13-bit) measurement at up to +-16 g. Digital...

SKU: DF-DRI0001 | Brand: DFRobot

The DFRobot 2×1A DC Motor Shield uses the L293 motor driver chip to control two 7–12 V DC motors at up to 1 A per channel. It stacks directly onto Arduino Uno and Arduino Mega boards, using pins 4, 5, 6, and 7 for mot...

SKU: DF-ROB0005 | Brand: DFRobot

The Turtle is a compact 2WD mobile robot platform designed for use with Arduino and other microcontroller boards. It comes as a kit with two geared DC motors, rubber wheels, a rear caster ball, an aluminium alloy chas...

SKU: AF-824 | Brand: Adafruit

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 12" (300mm) long and come in a 'strip' of 40 (4 pieces of each of ten rainbow colors). They have 0.1" male he...

SKU: AF-825 | Brand: Adafruit

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are approximately 3" (75mm) long and come in a 'strip' of 40 (4 pieces of each of ten rainbow colors). They have 0.1...

SKU: SF-SEN-09673 | Brand: SparkFun

A compact force sensitive resistor (FSR) from Interlink Electronics with a 4 mm (0.16″) diameter active sensing area. The resistance changes based on applied pressure — from over 1 MΩ with no pressure down to approxim...

SKU: AF-2045 | Brand: Adafruit

The Adafruit Si5351A Clock Generator Breakout lets you generate precise, arbitrary clock frequencies from 8 kHz to over 150 MHz using a simple I2C interface. With a precision 25 MHz crystal reference and internal PLLs...

SKU: SF-COM-09592 | Brand: SparkFun

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very basic 5mm LED with a green lens. It has a typical forward voltage of 2.0V and ...

SKU: SF-SEN-09570 | Brand: SparkFun

Melexis' MLX90614ESF-BAA is an infrared thermometer designed for non-contact temperature sensing. An internal 17-bit ADC and a powerful DSP contribute to the MLX90614’s high accuracy and resolution. It has a huge numb...

SKU: AF-2018 | Brand: Adafruit

Add a micro-slice standard solderless breadboard to your Perma-Proto or other perf-board. This 2x8 point solder-less breadboard is a good way to add some solderless prototyping space if you just need to...