Brands and Manufacturers

SKU: AF-1304 | Brand: Adafruit

The Adafruit Micro Lipo is a tiny USB charger for single-cell 3.7V/4.2V lithium polymer and lithium ion rechargeable batteries. Its gold-plated PCB-style USB connector plugs directly into any USB port — connect your b...

SKU: AF-2750 | Brand: Adafruit

Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 350mAh for a total of about...

SKU: AF-354 | Brand: Adafruit

Need a big battery for your project? This lithium ion pack is made of 2 balanced 2200mAh cells for a total of 4400mA capacity! The cells are connected in parallel and spot-welded to a protection circuit that provid...

SKU: AF-830 | Brand: Adafruit

A 4×AA battery holder with a snap-on cover and built-in on/off switch. Holds four AA batteries in series, outputting a nominal 6V (alkaline) or 4.8V (NiMH), making it a convenient portable power source for 5V microcon...

SKU: AF-449 | Brand: Adafruit

This 8×AA battery holder provides a portable 12V power source by connecting 8 AA batteries end-to-end in series. It delivers approximately 12VDC with alkaline cells (9.6V with NiMH rechargeables) and supports up to 2A...

SKU: AF-2164 | Brand: Adafruit

The classic L7805 linear voltage regulator in a TO-220 package, capable of delivering a clean, regulated 5.0 V output (±2%) from an input voltage of 7–35 V. With built-in current limiting and thermal shutdown protecti...

SKU: AF-4226 | Brand: Adafruit

The Adafruit INA260 is a precision DC power sensor that measures current, voltage, and power on either the high or low side of your circuit. With an integrated 2 mΩ (0.002Ω) 0.1% shunt resistor and 16-bit ADC, it hand...

SKU: AF-184 | Brand: Adafruit

Build your own breadboard-friendly adjustable power supply with this soldering kit. Based on the MIC2941 low-dropout regulator, it provides a guaranteed 1.25A output with only 40–400 mV dropout — far better than the L...

SKU: AF-875 | Brand: Adafruit

This 8×AA battery holder provides a portable power source with a built-in on/off switch and a standard 5.5 mm / 2.1 mm DC barrel plug for easy connection to Arduino boards, LED strips, motors, and other 12V devices. U...

SKU: AF-4711 | Brand: Adafruit

The AP3429A Buck Converter Breakout steps down 3.4–5.5V input to a stable 3.3V output at up to 1.2A, with 90–95% efficiency. It's ideal for powering 3.3V circuits from LiPo batteries, 3× alkaline cells, or USB power s...

SKU: AF-1400 | Brand: Adafruit

The Adafruit Push-button Power Switch Breakout lets you toggle DC power on and off with a simple button press. A latching analogue circuit uses a 3A P-FET to connect or disconnect the input to the output — press once ...

SKU: AF-3456 | Brand: Adafruit

This 5×AA battery holder delivers approximately 7.5V from five AA batteries, terminated with a 2.1mm DC barrel plug (centre positive). It provides the ideal voltage for Arduino boards and other development boards with...

SKU: AF-1331 | Brand: Adafruit

Keep it cool with a Peltier module. These unique electronic components can generate a temperature differential when powered. That is to say, apply 5V to the red (positive) and black (negative) wires and one side will ...

SKU: AF-5644 | Brand: Adafruit

The Adafruit 12V Bias Voltage Boost Converter uses the TI TPS61040 to generate 12V DC from as little as 3V input. This compact breakout is ideal for generating the bias voltage needed by OLED displays, LED string back...

SKU: AF-1459 | Brand: Adafruit

This inductive charging set provides wireless power transfer using a split-transformer design. The transmitter coil is powered with 9–12 V DC, and the receiver coil outputs 3.3 V DC — no direct wire connection between...

SKU: AF-1794 | Brand: Adafruit

When you need to switch a lot of power, P channel MOSFETs are best for the job. These P-FETs can switch over 60V and 25A (with proper heat-sinking) and are TO-220 package so they fit nicely into any breadboard or perf...

SKU: AF-248 | Brand: Adafruit

A 6×AA battery holder with a 5.5mm/2.1mm DC barrel plug, ready to power Arduino boards and other electronics with a standard DC jack. Use alkaline AAs for approximately 9V at 3000–4000mAh, or rechargeable NiMH cells f...

SKU: AF-3238 | Brand: Adafruit

This IEEE 802.3af PoE splitter separates power and data from a single PoE Ethernet cable, providing regulated 12VDC at up to 1A on a standard 2.1 mm DC barrel jack alongside a standard Ethernet data connection. It let...

SKU: AF-425 | Brand: Adafruit

A 4-pin Molex power cable that matches the hard drive/CD-ROM power connectors found on AT and ATX power supplies. Use it to tap into 5V or 12V DC from a desktop power supply for your projects — a convenient source of ...