Batteries

SKU: AF-770 | Brand: Adafruit

Keep your power source safe and toasty in these waterproof 2xAA battery holders. They're just like classic switched battery holders, but designed for survival! The case has a rubber gasket around the edge of the ca...

SKU: AF-2089 | Brand: Adafruit

A snap-in battery holder for Sony NP-F series camcorder batteries, with a pre-attached 2.1 mm DC barrel plug for powering 7 V DC devices. Clip in a compatible Li-Ion battery pack and connect directly to robots, Arduin...

SKU: AF-5580 | Brand: Adafruit

The Adafruit MAX17048 LiPoly/LiIon Fuel Gauge and Battery Monitor gives you accurate battery voltage and charge percentage readings for your 1S 3.7–4.2V lithium polymer or lithium ion battery. Instead of guessing rema...

SKU: TB-SB2933 | Brand: Little Bird

This range of Panasonic eneloop batteries have numerous advantages over regular rechargeables. Key characteristics include low self-discharge, they are pre-charged so can be used right out of the packet, and can be re...

SKU: TB-MB3563 | Brand: Little Bird

Keep your Eneloop and other Ni-MH batteries charged and ready to go with this lightweight Panasonic charger. It charges both AA and AAA batteries and includes 4× AA Eneloop batteries straight out of the box. Eneloop ...

SKU: DF-FIT1002 | Brand: DFRobot

The photonic thin-film battery is an advanced energy-harvesting solution that stands out from traditional solar cells and amorphous silicon photonic cells due to its higher conversion efficiency and output power. Made...

SKU: EF-EF08182 | Brand: ElecFreaks

This kit contains a micro:bit board, a USB cable and a battery holder. This is a basic kit for using micro:bit. Micro:bit board is launched by BBC which aims to help children at or above 7 grade to learn programming b...

SKU: DF-FIT0619 | Brand: DFRobot

This battery holder connects 3× AA batteries in series, providing approximately 4.5V from alkaline cells. It features a PH2.0-2P connector with a 15cm wire lead, making it compatible with DFRobot boards and other devi...

SKU: SF-PRT-15217 | Brand: SparkFun

The SparkFun LiPo Charger Plus is the souped-up power option in the SparkFun line of single-cell lithium polymer (LiPo) battery chargers. With this iteration, we've changed the input charge connector to USB-C and prov...

SKU: AF-3788 | Brand: Adafruit

A 4×AA battery holder with a built-in on/off switch and a 13cm (5″) power cable terminating in a centre-positive 2.1mm DC barrel jack. Provides convenient portable power with easy switching for development boards and ...

SKU: AF-1871 | Brand: Adafruit

A sewable breakout board with a CR2032 coin cell battery holder, built-in on/off switch, and 0.1" pitch breakout pins. The board provides two ground pins, one switched power pin, and one always-on power pin — giving y...

SKU: AF-2272 | Brand: Adafruit

This battery holder is designed to clip and hold Panasonic camcorder lithium-ion battery packs, providing a convenient high-capacity power source for custom projects. Simply snap your battery in, and use your existing...

SKU: SF-PRT-00091 | Brand: SparkFun

A classic 9V battery snap connector terminated with a 2-pin polarised Molex connector. Ideal for quick-connect battery power in breadboard and prototyping setups. Key Features Molex Terminated – 2-pin polarised con...

SKU: AF-617 | Brand: Adafruit

A 2-pack of standard alkaline AAA batteries for powering portable electronics, kits, and projects. These use alkaline (MnO2) chemistry with a voltage range of 1.6V (fresh) to 0.8V (depleted) and a capacity of approxim...

SKU: AF-3349 | Brand: Adafruit

A 4-pack of standard alkaline AA batteries for powering portable electronics, kits, and projects. These use alkaline (MnO2) chemistry with a voltage range of 1.6V (fresh) to 0.8V (depleted) and a typical capacity of a...

SKU: AF-654 | Brand: Adafruit

A standard CR2032 lithium coin cell battery providing 3V nominal output. This non-rechargeable cell is widely used in electronics projects, wearables, and sewable circuits. Specifications Type – CR2032 lithium coin...

SKU: SF-PRT-12718 | Brand: SparkFun

PCB mount clip to hold a AAA battery. Sold in single units, you’ll need two for each battery. These work great for small, low power applications that need a battery to run. Low cost and easy to use!Documents:Datasheet

SKU: AF-783 | Brand: Adafruit

A compact coin cell battery holder designed for small portable and wearable electronics projects. It holds two 20mm coin cells (CR2032 is the most common size) wired in series to provide 6V nominal output, with an on/...

SKU: AF-771 | Brand: Adafruit

Keep your power source safe and toasty in these waterproof 3xAA battery holders. They're just like classic switched battery holders, but designed for survival! The case has a rubber gasket around the edge of the ca...

SKU: DF-FIT0078 | Brand: DFRobot

A double-layer 6×AA battery holder with a stacked 3+3 cell arrangement for a more compact footprint. Creates a 7.2V rechargeable battery pack from NiMH/NiCd cells or a 9V pack from alkaline cells. Comes with 150mm (6"...