Batteries

SKU: AF-1870 | Brand: Adafruit

A simple sewable breakout board with a CR2032 coin cell battery holder pre-soldered on and 0.1" pitch breakout pins for easy connection. Ideal for powering very low-current projects or adding a battery backup circuit ...

SKU: AF-248 | Brand: Adafruit

A 6×AA battery holder with a 5.5mm/2.1mm DC barrel plug, ready to power Arduino boards and other electronics with a standard DC jack. Use alkaline AAs for approximately 9V at 3000–4000mAh, or rechargeable NiMH cells f...

SKU: AF-3286 | Brand: Adafruit

A slim 3×AAA battery holder with a built-in on/off switch, JST 2-pin connector, and an ergonomic belt clip. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making i...

SKU: AF-3287 | Brand: Adafruit

A compact 3×AA battery holder with a built-in on/off switch, JST 2-pin connector, and an ergonomic belt clip. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making...

SKU: SF-PRT-10512 | Brand: SparkFun

A snap-in 9V battery holder with a 5.5mm/2.1mm centre-positive barrel jack connector. The battery clicks securely into place, and three mounting holes allow you to attach the holder to an enclosure or chassis. Key Fe...

SKU: SF-PRT-10255 | Brand: SparkFun

The LiPower board is based on the incredibly versatile TPS61200 boost converter. The board is configured to be used with a LiPo battery, has solder jumper selectable 5V and 3.3V output, and an under voltage protection...

SKU: AF-770 | Brand: Adafruit

Keep your power source safe and toasty in these waterproof 2xAA battery holders. They're just like classic switched battery holders, but designed for survival! The case has a rubber gasket around the edge of the ca...

SKU: AF-2089 | Brand: Adafruit

A snap-in battery holder for Sony NP-F series camcorder batteries, with a pre-attached 2.1 mm DC barrel plug for powering 7 V DC devices. Clip in a compatible Li-Ion battery pack and connect directly to robots, Arduin...

SKU: AF-5580 | Brand: Adafruit

The Adafruit MAX17048 LiPoly/LiIon Fuel Gauge and Battery Monitor gives you accurate battery voltage and charge percentage readings for your 1S 3.7–4.2V lithium polymer or lithium ion battery. Instead of guessing rema...

SKU: DF-FIT1002 | Brand: DFRobot

The photonic thin-film battery is an advanced energy-harvesting solution that stands out from traditional solar cells and amorphous silicon photonic cells due to its higher conversion efficiency and output power. Made...

SKU: EF-EF08182 | Brand: ElecFreaks

This kit contains a micro:bit board, a USB cable and a battery holder. This is a basic kit for using micro:bit. Micro:bit board is launched by BBC which aims to help children at or above 7 grade to learn programming b...

SKU: DF-FIT0619 | Brand: DFRobot

This battery holder connects 3× AA batteries in series, providing approximately 4.5V from alkaline cells. It features a PH2.0-2P connector with a 15cm wire lead, making it compatible with DFRobot boards and other devi...

SKU: LB-LS1812 | Brand: Little Bird

Sick of your batteries all floating around in a drawer or box, and then when you come to use them, most are already flat.This had box keeps all your batteries standing upright and has a battery test to show if the bat...

SKU: SF-PRT-15217 | Brand: SparkFun

The SparkFun LiPo Charger Plus is the souped-up power option in the SparkFun line of single-cell lithium polymer (LiPo) battery chargers. With this iteration, we've changed the input charge connector to USB-C and prov...

SKU: AF-3788 | Brand: Adafruit

A 4×AA battery holder with a built-in on/off switch and a 13cm (5″) power cable terminating in a centre-positive 2.1mm DC barrel jack. Provides convenient portable power with easy switching for development boards and ...

SKU: AF-1871 | Brand: Adafruit

A sewable breakout board with a CR2032 coin cell battery holder, built-in on/off switch, and 0.1" pitch breakout pins. The board provides two ground pins, one switched power pin, and one always-on power pin — giving y...

SKU: AF-2272 | Brand: Adafruit

This battery holder is designed to clip and hold Panasonic camcorder lithium-ion battery packs, providing a convenient high-capacity power source for custom projects. Simply snap your battery in, and use your existing...

SKU: SF-PRT-07949 | Brand: SparkFun

A PCB-mount clip designed to hold a single AA battery. Ideal for small, low-power applications that need a compact battery solution. Sold individually — use two clips for a complete AA battery holder. Key Features ...

SKU: SF-PRT-00091 | Brand: SparkFun

A classic 9V battery snap connector terminated with a 2-pin polarised Molex connector. Ideal for quick-connect battery power in breadboard and prototyping setups. Key Features Molex Terminated – 2-pin polarised con...

SKU: AF-3349 | Brand: Adafruit

A 4-pack of standard alkaline AA batteries for powering portable electronics, kits, and projects. These use alkaline (MnO2) chemistry with a voltage range of 1.6V (fresh) to 0.8V (depleted) and a typical capacity of a...