Batteries

SKU: AF-2750 | Brand: Adafruit

Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of 350mAh for a total of about...

SKU: AF-354 | Brand: Adafruit

Need a big battery for your project? This lithium ion pack is made of 2 balanced 2200mAh cells for a total of 4400mA capacity! The cells are connected in parallel and spot-welded to a protection circuit that provid...

SKU: AF-830 | Brand: Adafruit

A 4×AA battery holder with a snap-on cover and built-in on/off switch. Holds four AA batteries in series, outputting a nominal 6V (alkaline) or 4.8V (NiMH), making it a convenient portable power source for 5V microcon...

SKU: AF-4288 | Brand: Adafruit

Here's a hand-held-size rechargeable battery pack for your Raspberry Pi (or Metro, or anything else that uses 5V!). This pack is intended for providing a lot of power to a smartphone, tablet, etc, but we found it d...

SKU: AF-67 | Brand: Adafruit

A 9V battery holder with a built-in on/off switch and a pre-attached 5.5mm/2.1mm centre-positive barrel plug. Ready to use out of the box — snap in a 9V battery, plug into your Arduino or other development board, and ...

SKU: AF-3859 | Brand: Adafruit

A 4×AA battery holder with premium jumper header wires that plug directly into a breadboard. No stripping or soldering required — just insert the header pins into your breadboard rails and start prototyping with porta...

SKU: DF-FIT0539 | Brand: DFRobot

A robust battery holder designed to house three 18650 lithium-ion cells in series, delivering a nominal 11.1V output through a standard DC 2.1mm power jack. Ideal for powering projects, robots, and portable electronic...

SKU: AF-449 | Brand: Adafruit

This 8×AA battery holder provides a portable 12V power source by connecting 8 AA batteries end-to-end in series. It delivers approximately 12VDC with alkaline cells (9.6V with NiMH rechargeables) and supports up to 2A...

SKU: WS-24760 | Brand: Waveshare

A compact uninterruptible power supply (UPS) module that supports simultaneous charging and power output. When external power is connected, it charges the batteries while providing a stable 5V output. If external powe...

SKU: EF-EF10095 | Brand: ElecFreaks

A 2×AA battery holder designed specifically for the BBC micro:bit. The built-in JST PH connector plugs directly into the micro:bit's battery socket, and the integrated on/off switch with a secure cover provides safe, ...

SKU: SF-PRT-12083 | Brand: SparkFun

This 4xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover, which is secured with a small phillips head screw. Another bonus is the ON/OFF swi...

SKU: AF-727 | Brand: Adafruit

A slim 3×AAA battery holder with a built-in on/off switch and JST 2-pin connector. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making it an ideal non-rechargeab...

SKU: DF-DFR0969 | Brand: DFRobot

A dual-slot 18650 battery holder with built-in charging and regulated power outputs, perfect for powering microcontrollers, sensors, and portable electronics projects. Simply install two 18650 lithium batteries and us...

SKU: DF-FIT0610 | Brand: DFRobot

This enclosed battery holder takes 3× AA batteries in series, providing approximately 4.5V from alkaline cells or 3.6V from NiMH/NiCd rechargeables. It features a built-in on/off switch and a sliding, removable cover ...

SKU: AF-4193 | Brand: Adafruit

A slim 2×AA battery holder with a built-in on/off switch and genuine JST PH connector. Two AA batteries in series provide approximately 3V — ideal for powering low-voltage electronics projects, microcontrollers, and p...

SKU: AF-1131 | Brand: Adafruit

A 500 mm extension cable with a JST-PH 2-pin socket on one end and a matching plug on the other. The colour-coded wires make it easy to verify correct polarity. Compatible with JST-PH terminated battery packs includin...

SKU: SF-PRT-10218 | Brand: SparkFun

A standard 9V alkaline battery (Rayovac). Suitable for powering Arduino boards, breadboard projects, and other electronics — use with a voltage regulator to get a stable 5V output. Key Features 9V Alkaline – Standa...

SKU: AF-4779 | Brand: Adafruit

This compact battery holder connects 3× AA batteries in series, providing 3.3–4.5V output — a similar range to lithium-ion/polymer batteries. It features a built-in on/off switch and a genuine JST-PH 2-pin connector w...

SKU: DF-FIT0079 | Brand: DFRobot

A simple 4-cell AA battery holder in a square (2×2) configuration. Features 5-inch tinned leads for easy soldering into your project. Provides 6V nominal output with four AA alkaline batteries, or 4.8V with rechargeab...

SKU: DF-FIT0043 | Brand: DFRobot

The second version of the 9V to Barrel Jack Adapter, now featuring a hard plastic battery snap for easier connection and disconnection. Plug a 9V battery into one end and connect the other to any device with a 5.5 × 2...