Batteries

SKU: SF-PRT-09835 | Brand: SparkFun

This is a simple 4 cell AA battery holder. The 5 inch cable is terminated with a standard 5.5x2.1mm, center positive barrel jack connector. The connector mates with the barrel jack on the Arduino (among a numbe...

SKU: AF-4191 | Brand: Adafruit

A slim 2×AAA battery holder with a built-in on/off switch and genuine JST PH connector. Two AAA batteries in series provide approximately 3V — ideal for powering low-voltage electronics projects, microcontrollers, and...

SKU: AF-3842 | Brand: Adafruit

A compact battery holder for three AA cells with an integrated power cable and DC barrel jack. The series configuration delivers approximately 3.6–4.5V depending on battery chemistry, making it a convenient power sour...

SKU: AF-3951 | Brand: Adafruit

A 2×AA battery holder with a built-in knife switch for controlling power. Unlike typical slide switches, the knife switch provides a clear visual indicator of open and closed circuit states — making it an excellent to...

SKU: LB-LR0335-Y | Brand: Little Bird

This 5-metre length of EL wire (electroluminescent wire) glows a vibrant yellow when powered by the included battery-operated inverter. EL wire is a flexible, phosphor-coated wire that produces a cool, even glow simil...

SKU: TB-PH9203 | Brand: Little Bird

This holder provides a simple way to add one AA cell to a battery-powered project. It is moulded in Delrin and uses corrosion-resistant nickel-plated springs and studs for reliable contact.The 150 mm bare lead connect...

SKU: AF-248 | Brand: Adafruit

A 6×AA battery holder with a 5.5mm/2.1mm DC barrel plug, ready to power Arduino boards and other electronics with a standard DC jack. Use alkaline AAs for approximately 9V at 3000–4000mAh, or rechargeable NiMH cells f...

SKU: AF-3286 | Brand: Adafruit

A slim 3×AAA battery holder with a built-in on/off switch, JST 2-pin connector, and an ergonomic belt clip. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making i...

SKU: AF-3287 | Brand: Adafruit

A compact 3×AA battery holder with a built-in on/off switch, JST 2-pin connector, and an ergonomic belt clip. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making...

SKU: SF-PRT-10512 | Brand: SparkFun

A snap-in 9V battery holder with a 5.5mm/2.1mm centre-positive barrel jack connector. The battery clicks securely into place, and three mounting holes allow you to attach the holder to an enclosure or chassis. Key Fe...

SKU: AF-770 | Brand: Adafruit

Keep your power source safe and toasty in these waterproof 2xAA battery holders. They're just like classic switched battery holders, but designed for survival! The case has a rubber gasket around the edge of the ca...

SKU: AF-2089 | Brand: Adafruit

A snap-in battery holder for Sony NP-F series camcorder batteries, with a pre-attached 2.1 mm DC barrel plug for powering 7 V DC devices. Clip in a compatible Li-Ion battery pack and connect directly to robots, Arduin...

SKU: EF-EF08182 | Brand: ElecFreaks

This kit contains a micro:bit board, a USB cable and a battery holder. This is a basic kit for using micro:bit. Micro:bit board is launched by BBC which aims to help children at or above 7 grade to learn programming b...

SKU: DF-FIT0619 | Brand: DFRobot

This battery holder connects 3× AA batteries in series, providing approximately 4.5V from alkaline cells. It features a PH2.0-2P connector with a 15cm wire lead, making it compatible with DFRobot boards and other devi...

SKU: LB-LS1812 | Brand: Little Bird

Sick of your batteries all floating around in a drawer or box, and then when you come to use them, most are already flat.This had box keeps all your batteries standing upright and has a battery test to show if the bat...

SKU: AF-3788 | Brand: Adafruit

A 4×AA battery holder with a built-in on/off switch and a 13cm (5″) power cable terminating in a centre-positive 2.1mm DC barrel jack. Provides convenient portable power with easy switching for development boards and ...

SKU: AF-2272 | Brand: Adafruit

This battery holder is designed to clip and hold Panasonic camcorder lithium-ion battery packs, providing a convenient high-capacity power source for custom projects. Simply snap your battery in, and use your existing...

SKU: SF-PRT-07949 | Brand: SparkFun

A PCB-mount clip designed to hold a single AA battery. Ideal for small, low-power applications that need a compact battery solution. Sold individually — use two clips for a complete AA battery holder. Key Features ...

SKU: SF-PRT-12718 | Brand: SparkFun

PCB mount clip to hold a AAA battery. Sold in single units, you’ll need two for each battery. These work great for small, low power applications that need a battery to run. Low cost and easy to use!Documents:Datasheet

SKU: AF-771 | Brand: Adafruit

Keep your power source safe and toasty in these waterproof 3xAA battery holders. They're just like classic switched battery holders, but designed for survival! The case has a rubber gasket around the edge of the ca...