Arduino

SKU: AF-4210 | Brand: Adafruit

This 4-wire cable is a little over 100mm / 4" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching f...

SKU: DF-DFR0265 | Brand: DFRobot

The DFRobot Gravity IO Expansion Shield V7.1 simplifies Arduino prototyping by breaking out all digital and analogue pins into colour-coded 3-pin (Signal, Voltage, Ground) Gravity connectors. Plug in sensors, actuator...

SKU: SF-SEN-11050 | Brand: SparkFun

This sealed digital temperature probe lets you precisely measure temperatures in wet environments with a simple 1-Wire interface. The DS18B20 provides 9 to 12-bit (configurable) temperature readings over a 1-Wire i...

SKU: DF-SEN0205 | Brand: DFRobot

A photoelectric liquid level sensor that uses optical principles to detect the presence or absence of liquid. With no moving parts, it requires minimal calibration and offers high sensitivity and long service life. Th...

SKU: DF-DFR1096 | Brand: DFRobot

The Arduino Nano ESP32 brings the ESP32-S3 (u-blox NORA-W106 module) into the familiar Nano form factor with a USB-C connector. It supports both Arduino and MicroPython programming, making it an accessible entry point...

SKU: AF-4401 | Brand: Adafruit

This 4-wire cable is a little over 200mm / 7.8" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching fe...

SKU: LB-LR0293-29 | Brand: Little Bird

These compact jumper cables feature a premium female header on one end and a grippy mini alligator clip on the other — perfect for breadboarding with non-header-friendly boards and components. Clip onto a micro:bit, C...

SKU: SF-PRT-12044 | Brand: SparkFun

This red Mini Breadboard is a great way to prototype your small projects! With 170 tie points there’s just enough room to build and test simple circuits; They’re also great for breaking out DIP package ICs to jumpe...

SKU: DF-DFR0251 | Brand: DFRobot

A relay is an electrically operated switch, which has a control system (also known as the input circuit) and the controlled system (also known as the output circuit), usually used in automatic control circuit. It i...

SKU: AF-64 | Brand: Adafruit

This is a cute half size breadboard, good for small projects. It's 2.2" x 3.4" (5.5 cm x 8.5 cm) with a standard double-strip in the middle and two power rails on both sides. You can pull the power rails off easily to...

SKU: SF-DEV-11235 | Brand: SparkFun

The Arduino and Breadboard Holder is a sturdy plastic base plate that keeps your Arduino and breadboard neatly organised during prototyping. The board mounts with two included screws using the standard Arduino mountin...

SKU: DF-SEN0189 | Brand: DFRobot

The Gravity Analog Turbidity Sensor measures water clarity by detecting the level of suspended particles. It works by measuring light transmittance and scattering rate, which change with the amount of total suspended ...

SKU: AF-1956 | Brand: Adafruit

A pack of 20 premium male-to-male jumper wires in a convenient ribbon cable format. Each wire is 75 mm (3") long with 0.1" (2.54 mm) male header contacts on both ends, fitting cleanly onto standard-pitch headers. The...

SKU: DF-SEN0503 | Brand: DFRobot

An infrared break-beam sensor pair for simple, reliable motion detection. The emitter sends a beam of invisible IR light to the receiver — when an object passes between them and breaks the beam, the receiver outputs a...

SKU: SF-SEN-14709 | Brand: SparkFun

The AH1815 is an integrated Hall-Effect non-latched sensor. That’s nice but what does it do? Holding a magnet near the sensor will cause the output pin to toggle. This makes for a robust presence sensor. A reed sen...

SKU: AF-2167 | Brand: Adafruit

Infrared (IR) break-beam sensors are a simple way to detect motion. They work by having an emitter side that sends out a beam of human-invisible IR light, then a receiver across the way which is sensitive to tha...

SKU: DF-DFR0095 | Brand: DFRobot

An infrared transmitter is simply a Light Emitting Diode which generates IR light (invisible IR light)--light with a wavelength of between 1 mm and 750 nanometers, and some associated circuitry. In an infrared ...

SKU: DF-DFR0457 | Brand: DFRobot

In most Arduino projects, relays are the first choice to drive some large current device. It requires a certain amount of current to drive the internal coil to pick-up contact. But for some MCU, like Intel Edison,...

SKU: DF-FIT0080 | Brand: DFRobot

A 4-cell AA battery holder in a square (2×2) configuration with a sliding removable cover and a built-in ON/OFF switch. Features 5-inch tinned leads for easy soldering. The cover keeps batteries secure, and the switch...

SKU: DF-DFR0575 | Brand: DFRobot

Is FireBeetle-ESP32 too big for your projects? Why not try our newly launched Beetle-ESP32. This Beetle-ESP32 Microcontroller of 1.38”×1.34”small size is a simplified version of FireBeetle-ESP32 and specially designed...