Arduino

SKU: AF-3200 | Brand: Adafruit

The Teensy 3.x Feather Adapter rearranges the pins of a Teensy 3.x board to match the Adafruit Feather form factor and pinout. This allows the Teensy to work with the full range of FeatherWing add-ons — motor drivers,...

SKU: AF-374 | Brand: Adafruit

These 1-wire digital temperature sensors are fairly precise (±0.5°C over much of the range) and can give up to 12 bits of precision from the onboard digital-to-analog converter. They work great with any microcontro...

SKU: AF-386 | Brand: Adafruit

The DHT11 is a basic, ultra low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air, and spits out a digital signal on the data pin (no an...

SKU: DF-SEN0177 | Brand: DFRobot

The Gravity Laser PM2.5 Air Quality Sensor uses laser scattering to measure suspended particulate matter concentrations in the air. It detects particles from 0.3 to 10 µm in diameter and outputs digital concentration ...

SKU: SF-PRT-13010 | Brand: SparkFun

This is a simple 2x3 female PTH header. This header is in the common configuration for an ISP connector. Each pin has a spacing of 0.1" in between each other. Documents: Datasheet

SKU: SF-COM-10613 | Brand: SparkFun

A digital potentiometer that lets you control a voltage divider with serial signals from your microcontroller. Wire it up like a standard potentiometer, then use digital commands to adjust the wiper position — no mech...

SKU: SF-BOB-10160 | Brand: SparkFun

Here is a real time clock based on the DS3234 Real Time Clock IC. The DS3234 is a low-cost, extremely accurate SPI bus real-time clock with an integrated temperature-compensated crystal oscillator and crystal. Th...

SKU: DF-KIT0111 | Brand: DFRobot

The Gravity Starter Kit for Arduino is a plug-and-play electronics toolkit designed for beginners and makers getting started with the Arduino platform. It includes a DFRduino UNO R3 microcontroller (fully compatible w...

SKU: SF-ROB-12567 | Brand: SparkFun

This buzzer is an add-on for your RedBot that gives your robot the ability to make awesome beep-boop noises or alerts when something interesting (or terrible) happens. The buzzer works by making use of two I/O pi...

SKU: AF-813 | Brand: Adafruit

Design a clock, timer or counter into your next project using our pretty 4-digit seven-segment display. These bright crisp displays are good for adding numeric output. Besides the four 7-segments, there are decimal...

SKU: DF-DFR0021-W | Brand: DFRobot

A simple digital white LED module with Gravity interface. Plugs directly into DFRobot IO/Sensor expansion shields for easy integration with Arduino projects — ideal for beginners learning digital output control. Spec...

SKU: DF-SEN0018 | Brand: DFRobot

This is a simple to use arduino motion sensor. Power it up and wait 1-2 seconds for the sensor to get a snapshot of the still room. If anything moves after that period, the 'alarm' pin will go low. This sensor c...

SKU: DF-DFR0053 | Brand: DFRobot

This arduino Slide Position Sensor is based on straight-slip slide potentiometer sensor. The sensor is able to give provide the position of the slider which is often considered as a linear potentiometer . The ...

SKU: DF-FIT0031 | Brand: DFRobot

A pack of 10 analog sensor cables designed for use with DFRobot IO Expansion Shields and compatible analog sensors. Each cable connects a sensor to the expansion shield's analog ports, making wiring quick and tidy. E...

SKU: SF-SEN-09404 | Brand: SparkFun

This is a simple-to-use compressed natural gas (CNG) sensor, suitable for sensing natural gas (composed of mostly Methane [CH4]) concentrations in the air. The MQ-4 can detect natural gas concentrations anywhere from ...

SKU: LB-LR0122 | Brand: Little Bird

This module consists of 64 LEDs with MAX7219 driver chip. It can control 64 LEDs by 16-bit data serial input and output. If you want to control it, you only need to control three IO ports. It support for cascading mul...

SKU: KS-FB0001 | Brand: Keyestudio

 The FoxBit is a versatile development board built around the powerful ESP32-D0WDQ6 dual-core microcontroller, designed for education, makers, and electronics enthusiasts. Ideal for IoT, STEAM education, smart c...

SKU: DF-SEN0672 | Brand: DFRobot

The Benewake TFS20-L is an ultra-compact ToF LiDAR sensor weighing just 1.35g. With 20m range, centimetre-level accuracy, and 100K LUX sunlight resistance, it's designed for drones, robots, and space-constrained appli...

SKU: SF-PRT-10037 | Brand: SparkFun

This is a front faceplate that lets your Crib for Arduino accommodate the Arduino and Ethernet Shield in one secure, clean looking, easy to acces package. Have you ever tried to punch or cut square holes for the Ard...

SKU: ATTINY85-20MURTR-ND | Brand: Little Bird

Do you have a project that needs the ATTINY85-20MURTR-ND?We purchased these back in 2021 and then, never made anything with them.They have been kept in a dry cabinet ever since.The packet says it was 1000, we have pro...