Arduino

SKU: AF-1774 | Brand: Adafruit

The 2.8" TFT Display with Resistive Touchscreen is a bare LCD module featuring 320×240 resolution with individual RGB pixel control. Driven by the ILI9341 chipset, it supports SPI (3- or 4-wire), 8-bit parallel, and 1...

SKU: AF-2168 | Brand: Adafruit

Infrared (IR) break-beam sensors are a simple way to detect motion. They work by having an emitter side that sends out a beam of human-invisible IR light, then a receiver across the way which is sensitive to that s...

SKU: DF-FIT0043 | Brand: DFRobot

The second version of the 9V to Barrel Jack Adapter, now featuring a hard plastic battery snap for easier connection and disconnection. Plug a 9V battery into one end and connect the other to any device with a 5.5 × 2...

SKU: DF-SEN0133 | Brand: DFRobot

This is an Arduino hydrogen gas sensor. It has high sensitivity to Hydrogen (H2) and less sensitivity to alcohol, LPG,cooking fumes . Hydrogen gas is highly flammable and will burn in air at a very wide range...

SKU: DF-DFR0201 | Brand: DFRobot

The Arduino Leonardo is a microcontroller board based on the ATmega32U4, offering the same flash, RAM, and capabilities as the ATmega328 found in the Uno. The key difference is built-in USB communication, allowing the...

SKU: AF-2822 | Brand: Adafruit

If we could eat headers, we'd have them for breakfast, lunch, and dinner.  But we can't :( So we're making the best of it and selling them! This 2x20-pin strip male header is a great way to a...

SKU: SF-COM-00315 | Brand: SparkFun

The SN754410 is a quad half H-bridge motor driver IC capable of driving DC motors, stepper motors, and other inductive loads. It accepts TTL 5V logic inputs and can drive motors from 4.5V to 36V at up to 1A continuous...

SKU: DF-DRI0023 | Brand: DFRobot

INTRODUCTION Do you want to do some projects with stepper motors such as a drafting instrument, a 3D printer, an auto curtain......? As we all know, regular stepper motors are hard to dri...

SKU: DF-DFR0024 | Brand: DFRobot

While there are many types of temperature sensors available in the market, the DS18B20 arduino Temperature Sensor form DALLAS is the best choice in applications which require high accuracy and high reliability. It...

SKU: SF-PRT-11476 | Brand: SparkFun

This barrel jack plug is great for adding a common connector to the end of our wires. This jack is compatible with 5.5mm barrel jacks that have a 2.1mm center pole diameter. The outer shell unscrews to reveal solder t...

SKU: DF-DFR0029-G | Brand: DFRobot

The DFRobot Gravity Digital Push Button (Green) is a simple momentary switch with an on-board LED indicator, designed for the Gravity interface system. It features an immersion gold PCB surface, a bright green cap, an...

SKU: DF-DFR0023 | Brand: DFRobot

This is an Arduino Temperature Sensor based on LM35 temperature chip. A Temperature Sensor can be used to detect ambient air temperature.The LM35 chip is produced by National Semiconductor Corporation and offers a fun...

SKU: AF-184 | Brand: Adafruit

Build your own breadboard-friendly adjustable power supply with this soldering kit. Based on the MIC2941 low-dropout regulator, it provides a guaranteed 1.25A output with only 40–400 mV dropout — far better than the L...

SKU: SF-PRT-11417 | Brand: SparkFun

These headers are made to work with the Arduino Uno R3, Leonardo and new Arduino boards going forward. They are the perfect height for clearing the USB-B connector and great for stacking multiple shields. This kit ...

SKU: SF-PRT-11376 | Brand: SparkFun

A 10-pin female header with extra-long legs, designed for stacking Arduino R3-compatible shields. The extended pins pass through a shield's PCB and connect to the board below, letting you stack multiple shields on a s...

SKU: DF-DFR0165 | Brand: DFRobot

Say goodbye to messy cables and clueless pluging/unpluging! This Sensor Shield is a powerful expansion shield for Arduino Mega Due. It is large enough to carry up to 3 Xbee slots, 1 microSD slot and shield headers...

SKU: SF-DEV-11364 | Brand: SparkFun

The LilyTwinkle is a tiny little LilyPad board designed to add some twinkle to your project. Even though it’s as small as some of the LilyPad sensors, this board actually has an ATtiny microcontroller on it so it’s...

SKU: DF-SEN0043 | Brand: DFRobot

An analog ambient light sensor based on the TEMT6000 detector, which has a spectral response closely matching the human eye with very low IR sensitivity. It outputs an analog voltage proportional to the ambient light ...

SKU: DF-DFR0305 | Brand: DFRobot

The Romeo BLE is an all-in-one Arduino-compatible robot control board from DFRobot with integrated Bluetooth 4.0. It combines an ATmega328P microcontroller, a dual-channel DC motor driver (2 A max), and a TI CC2540 BL...

SKU: DF-DRI0017 | Brand: DFRobot

The DFRobot 2×2A Motor Shield uses the L298P dual full-bridge driver chip to control two 4.8–35 V DC motors at up to 2 A per channel. It stacks directly onto Arduino Uno and Arduino Mega boards, using PWM pins 10 and ...