Arduino

SKU: AF-2024 | Brand: Adafruit

The Adafruit Capacitive Touch Shield brings 12 channels of capacitive touch sensing to any Arduino using the MPR121 chip. Each sensor has a "figure 8" pad with holes designed for quick alligator clip connections — att...

SKU: DF-SEN0006 | Brand: DFRobot

The latest model SRF05 Detection range of 3 cm from the original SRF04 -3 m, increased to 1 cm -4 meters. RF04 is compatible with the original. Also has smaller side lobes. Ultrasonic module can be used to identi...

SKU: DF-SEN0005 | Brand: DFRobot

This low cost SFR02 ultrasonic ranger has both I2C and Serial interfaces. New AutoTune algorithms intelligently back the minimum range right up to the transducer ringdown for the very best performance possible, aut...

SKU: DF-TEL0026 | Brand: DFRobot

A Bluetooth 2.0 serial module for Arduino, featuring the CSR BC417143 chip with a double-board design for electrostatic protection. Provides transparent serial data communication over Bluetooth with a configurable bau...

SKU: DF-DFR0108 | Brand: DFRobot

The Arduino Mega 2560 Rev3 is a microcontroller board based on the ATmega2560, offering significantly more I/O than standard Arduino boards. With 54 digital I/O pins, 16 analog inputs, and 4 hardware serial ports, it'...

SKU: DF-DFR0091 | Brand: DFRobot

A 128 × 64 pixel graphic LCD module based on the ST7920 controller, featuring a blue backlight with white characters. Supports both parallel (8/4-bit) and SPI (3-wire serial) interfaces, with parallel mode set as the ...

SKU: DF-FIT0101 | Brand: DFRobot

This is a really easy use prototyping plate. Basically you can put everything from Arduino board to sensors, even a motor on top of it. It fits M2-M3 screws. NOTE: This product does not ship with the board shown abov...

SKU: DF-DFR0090 | Brand: DFRobot

An 8-digit serial LED display module that uses an SPI (3-wire) interface, requiring only three I/O pins from your Arduino or microcontroller. Multiple modules can be daisy-chained together for longer displays. The fli...

SKU: PL-2508 | Brand: Pololu

This shield makes it easy to build an Arduino-controlled Zumo robot. The shield mounts onto an assembled Zumo chassis, connecting directly to the chassis’s battery terminals and motors, and the Arduino plugs into ...

SKU: DF-DFR0117 | Brand: DFRobot

Arduino has a small amount of data storage space, The Arduino UNO has 32k. It doesn't have enough space if you want to store a lot of data. Therefore, we need to add an EEPROM Data Storage Module to increase its stora...

SKU: DF-SEN0228 | Brand: DFRobot

The Gravity VEML7700 is a high-accuracy digital ambient light sensor that outputs readings directly in lux (lx) over an I²C interface. Built around the Vishay VEML7700 IC, it features a 16-bit ADC, a high-sensitivity ...

SKU: DF-DFR0141 | Brand: DFRobot

The Rainbow LED Ring V3 features 12 individually addressable SMD RGB LEDs arranged in a ring, each controllable for brightness and colour. It comes with a pre-loaded bootloader containing several built-in LED animatio...

SKU: DF-DFR0021-R | Brand: DFRobot

A simple red LED module with a Gravity 3-pin digital interface for plug-and-play connection to Arduino and other microcontrollers via a Gravity IO Expansion Shield. Ideal for beginners learning digital output control....

SKU: AF-2547 | Brand: Adafruit

For advanced NeoPixel fans, we now have a bendable, Flexible 16x16 NeoPixel LED Matrix! Control all 256 ultra-bright LEDs using a single microcontroller pin, set each LED as you wish to scroll messages or draw litt...

SKU: DF-FIT0145 | Brand: DFRobot

A waterproof DC-DC step-down/step-up converter that accepts 8–40V DC input and delivers a stable 12V output at up to 6A (72W). Ideal for powering embedded PCs, single-board computers, and robot electronics from a wide...

SKU: AF-2653 | Brand: Adafruit

Get your Particle (formally known as Spark) Photon moving with a PhoBot Robotics shield. No, this is not a robot that makes you a delicious bowl of Vietnamese soup.  Instead, it's a board from Simon Monk ...

SKU: DF-FIT0147 | Brand: DFRobot

This is a 6-pin female header, with extra long legs -- great for stacking Arduino shields.Pins are spaced by 0.1". APPLICATIONS PCB Arduino Shield Header SPECIFICATIONS18.6 x 15.8 x 2.5(mm)(0.73x0.62x0.09") SHIPPING...

SKU: DF-FIT0106 | Brand: DFRobot

A pack of ten 6-pin female headers with standard 0.1″ (2.54mm) pin spacing. Commonly used for Arduino shield connections and general prototyping. Key Features Standard 0.1″ Pitch – Compatible with breadboards, Ardu...

SKU: DF-DFR0162 | Brand: DFRobot

This is Version 2.0 of the Xboard. The main improvement is that it now operates at 5V, making it compatible with most sensors and I2C protocol without the need of a voltage level converter. The XBoard is a...

SKU: DF-FIT0164 | Brand: DFRobot

This is a 6-pin female header, with extra long legs -- great for stacking Arduino shields. SPECIFICATIONS Pins are spaced by 0.1" Size: 15.58x23.05x2.4mm(0.9x0.6x0.1") (Pins: 15 mm)(Pin...