Arduino Shields

SKU: DF-DFR0265 | Brand: DFRobot

The DFRobot Gravity IO Expansion Shield V7.1 simplifies Arduino prototyping by breaking out all digital and analogue pins into colour-coded 3-pin (Signal, Voltage, Ground) Gravity connectors. Plug in sensors, actuator...

SKU: AF-1438 | Brand: Adafruit

The Adafruit Motor/Stepper/Servo Shield v2.3 is the upgraded successor to the original Motor Shield, delivering higher current, lower voltage drop, and a fully I2C-based design that frees up your Arduino's PWM pins. D...

SKU: DF-DFR0762 | Brand: DFRobot

Specially designed for FireBeetle 2 series (M0, ESP32-E), this Gravity IO expansion shield offers various ports including digital, analog, I2C, UART, SPI, etc. Also, it comes with power input socket for connecting ext...

SKU: DF-DFR0502 | Brand: DFRobot

Gravity IO Expansion Shield with Motor Driver is a new product designed for Arduino Boards. It combines IO Expansion Shield and DC Motor Driver Shield, equipped with Gravity sensor interface and...

SKU: EC-ARS27361T | Brand: Elecrow

This motor shield uses dual TB6612 MOSFET drivers and a PCA9685PW I2C PWM controller to drive up to 4 DC motors or 2 stepper motors from an Arduino or compatible board. All motor control and speed management is handle...

SKU: DF-DFR0012 | Brand: DFRobot

The Arduino Nano I/O Sensor Shield acts as an expansion board for the Arduino Nano and DFRduino Nano microcontrollers. There are several different options for power input. The form factor of the Nano I/O Shield bo...

SKU: SF-WRL-18567 | Brand: SparkFun

Ultra. Low. Power. Arguably the best three words in the IoT world. SparkFun has teamed up with ARM and Dialog to provide you with this Qwiic WiFi Shield based around the DA16200 module. The DA16200 is a fully integrat...

SKU: EC-AS00121CTH | Brand: Elecrow

This Capacitive Touch Shield has 9 build-on capacitive touchpads, and the other 3 electrodes for further usage. With this shield, you can have a total of 12 touch-sensitive buttons. This Shield uses the MPR121 which i...

SKU: EC-CDE20032P | Brand: Elecrow

An Arduino Uno shield that makes it easy to drive a 16×32 RGB LED matrix panel with a HUB75 connector. Instead of wiring up 12 individual jumper wires, this shield provides a matching 2×8 IDC connector for a clean, re...

SKU: DF-DFR0491 | Brand: DFRobot

The Gravity IO Expansion Shield breaks out all GPIO pins from the LattePanda into Gravity-compatible 3-pin colour-coded connectors, providing plug-and-play access to hundreds of Gravity sensors and modules. Each pin i...

SKU: DF-DFR0578 | Brand: DFRobot

Gravity: I/O Expansion Shield for OpenMV Cam H7 & H7 Plus is an expansion shield specially designed for the OpenMV Cam H7 and OpenMV Cam H7 Plus. It is compatible with various sensors and electronic modules of Gravity...

SKU: SF-GPS-15136 | Brand: SparkFun

With GPS you are able to know where you are, where you’re going, and how to get there anywhere on Earth within 30 seconds. This means the higher the accuracy the better! GPS Real Time Kinematics (RTK) has mastered dia...

SKU: AF-2024 | Brand: Adafruit

The Adafruit Capacitive Touch Shield brings 12 channels of capacitive touch sensing to any Arduino using the MPR121 chip. Each sensor has a "figure 8" pad with holes designed for quick alligator clip connections — att...

SKU: DF-DFR0117 | Brand: DFRobot

Arduino has a small amount of data storage space, The Arduino UNO has 32k. It doesn't have enough space if you want to store a lot of data. Therefore, we need to add an EEPROM Data Storage Module to increase its stora...

SKU: DF-DFR0407 | Brand: DFRobot

The Arduino 9 Axes Motion Shield is based on the Bosch BNO055 absolute orientation sensor — a System in Package (SiP) integrating a triaxial 14-bit accelerometer, 16-bit gyroscope (±2000°/s range), triaxial geomagneti...

SKU: DF-DFR0382 | Brand: DFRobot

An Arduino-compatible shield featuring a 4-digit 7-segment digital tube display (common cathode, 0.56") with 5 input buttons. Uses I2C to drive the display, providing an easy interface for menus, controls, and numeric...

SKU: DF-DFR0375 | Brand: DFRobot

INTRODUCTION The Cookie I/O expansion shield is designed for beginners to electronics. The shield is directly compatible with the gravity series. We have implemented fail-safe systems to pre...

SKU: AF-715 | Brand: Adafruit

The Adafruit I²C Controlled + Keypad Shield Kit lets you drive a 16×2 character LCD and read 5 navigation buttons using only two I²C pins on your Arduino. This frees up the 9+ digital pins that a standard LCD connecti...

SKU: SF-DEV-28021 | Brand: SparkFun

Add stand-alone audio playback to an Arduino project with this serial MP3 player shield based on the MY1690X decoder IC. It can play MP3 and WAV files from a standard microSD card, making it handy for music, voice pro...