Arduino Shields

SKU: LB-OWL-SENSOR | Brand: Little Bird

Build your electronics projects easier than ever with the use of this sensor shield expansion board. It makes connecting many input devices and output devices to the correct Arduino pins. This great board definitel...

SKU: DF-DFR0265 | Brand: DFRobot

The DFRobot Gravity IO Expansion Shield V7.1 simplifies Arduino prototyping by breaking out all digital and analogue pins into colour-coded 3-pin (Signal, Voltage, Ground) Gravity connectors. Plug in sensors, actuator...

SKU: AF-1438 | Brand: Adafruit

The Adafruit Motor/Stepper/Servo Shield v2.3 is the upgraded successor to the original Motor Shield, delivering higher current, lower voltage drop, and a fully I2C-based design that frees up your Arduino's PWM pins. D...

SKU: DF-DFR0762 | Brand: DFRobot

Specially designed for FireBeetle 2 series (M0, ESP32-E), this Gravity IO expansion shield offers various ports including digital, analog, I2C, UART, SPI, etc. Also, it comes with power input socket for connecting ext...

SKU: DF-DFR0502 | Brand: DFRobot

Gravity IO Expansion Shield with Motor Driver is a new product designed for Arduino Boards. It combines IO Expansion Shield and DC Motor Driver Shield, equipped with Gravity sensor interface and...

SKU: EC-ARS27361T | Brand: Elecrow

This motor shield uses dual TB6612 MOSFET drivers and a PCA9685PW I2C PWM controller to drive up to 4 DC motors or 2 stepper motors from an Arduino or compatible board. All motor control and speed management is handle...

SKU: AF-1411 | Brand: Adafruit

The Adafruit 16-Channel PWM/Servo Shield brings PCA9685-based servo and PWM control to any Arduino in a convenient shield format. Using only I2C (SCL and SDA), the shield provides 16 channels of 12-bit PWM output with...

SKU: DF-DFR0012 | Brand: DFRobot

The Arduino Nano I/O Sensor Shield acts as an expansion board for the Arduino Nano and DFRduino Nano microcontrollers. There are several different options for power input. The form factor of the Nano I/O Shield bo...

SKU: AF-714 | Brand: Adafruit

This new Adafruit shield makes it easy to use a 16x2 Character LCD. We really like the RGB LCDs we stock in the shop both the RGB negative and RGB positive. Unfortunately, these LCDs do require quite a few digital ...

SKU: DF-DFR0327 | Brand: DFRobot

The Gravity Arduino Shield for Raspberry Pi brings Arduino-compatible I/O to your Raspberry Pi B+, 2B, 3B, 3B+, or 4B. Built around the ATmega32u4 (Arduino Leonardo), it sits on top of your Pi and gives you access to ...

SKU: PL-5030 | Brand: Pololu

The Motoron M3S256 Triple Motor Controller Shield for Arduino makes it easy to control DC motors from an Arduino or Arduino-compatible board through an I²C interface. Each module can independently control up to three ...

SKU: SF-WRL-18567 | Brand: SparkFun

Ultra. Low. Power. Arguably the best three words in the IoT world. SparkFun has teamed up with ARM and Dialog to provide you with this Qwiic WiFi Shield based around the DA16200 module. The DA16200 is a fully integrat...

SKU: EC-AS00121CTH | Brand: Elecrow

This Capacitive Touch Shield has 9 build-on capacitive touchpads, and the other 3 electrodes for further usage. With this shield, you can have a total of 12 touch-sensitive buttons. This Shield uses the MPR121 which i...

SKU: EC-CDE20032P | Brand: Elecrow

An Arduino Uno shield that makes it easy to drive a 16×32 RGB LED matrix panel with a HUB75 connector. Instead of wiring up 12 individual jumper wires, this shield provides a matching 2×8 IDC connector for a clean, re...

SKU: DF-DFR0491 | Brand: DFRobot

The Gravity IO Expansion Shield breaks out all GPIO pins from the LattePanda into Gravity-compatible 3-pin colour-coded connectors, providing plug-and-play access to hundreds of Gravity sensors and modules. Each pin i...

SKU: DF-DFR0578 | Brand: DFRobot

Gravity: I/O Expansion Shield for OpenMV Cam H7 & H7 Plus is an expansion shield specially designed for the OpenMV Cam H7 and OpenMV Cam H7 Plus. It is compatible with various sensors and electronic modules of Gravity...

SKU: SF-DEV-17119 | Brand: SparkFun

The SparkFun Qwiic Shield for Teensy adds four Qwiic (I2C) connectors to your Teensy board, providing quick access to the SparkFun Qwiic ecosystem of sensors, actuators, and displays. Sized to fit the Teensy 4.0, Teen...

SKU: SF-GPS-15136 | Brand: SparkFun

With GPS you are able to know where you are, where you’re going, and how to get there anywhere on Earth within 30 seconds. This means the higher the accuracy the better! GPS Real Time Kinematics (RTK) has mastered dia...

SKU: AF-2024 | Brand: Adafruit

The Adafruit Capacitive Touch Shield brings 12 channels of capacitive touch sensing to any Arduino using the MPR121 chip. Each sensor has a "figure 8" pad with holes designed for quick alligator clip connections — att...

SKU: PL-2508 | Brand: Pololu

This shield makes it easy to build an Arduino-controlled Zumo robot. The shield mounts onto an assembled Zumo chassis, connecting directly to the chassis’s battery terminals and motors, and the Arduino plugs into ...