All Products

SKU: LB-LR0379 | Brand: Little Bird

This crimping tool can be used to crimp both male and female versions of our Tamiya connector crimp pins, mini Tamiya connector crimp pins, JST RCY connector crimp pins, JR crimp pins, Futa...

SKU: AF-3686 | Brand: Adafruit

Breathe easy, knowing that you can track and sense the quality of the air around you with the PM2.5 Air Quality Sensor with Breadboard Adapter particulate sensor. Mad Max & Furiosa definitely should have ho...

SKU: AF-3659 | Brand: Adafruit

Move fluid from here to there with this very nice elastomeric silicone tubing, specifically for our peristaltic pump. It's one meter long and fully silicone with the correct diameter to give great peristaltic pe...

SKU: AF-1669 | Brand: Adafruit

Listen up! This set of two 2.8" x 1.2" speakers are the perfect addition to any audio project where you need 4 ohm impedance and 3W or less of power. We particularly like these speakers as they are small and enclos...

SKU: AF-1756 | Brand: Adafruit

Add a little sparkle to your wearable project with Adafruit LED Sequins. These tiny sewable LED boards are the simpler sibling of Flora NeoPixels — they display a single colour with no digital control needed, making t...

SKU: AF-2215 | Brand: Adafruit

A 16.000 MHz quartz crystal in the HC49/US short-style package, supplied with two 20pF load capacitors. The crystal provides higher precision than ceramic resonators, with 30 PPM tolerance and 50 PPM stability — suita...

SKU: AF-2166 | Brand: Adafruit

A low-dropout (LDO) 3.3 V linear voltage regulator based on the ST L4931 in a TO-92 package. With just 0.4 V dropout, it delivers a clean, regulated 3.3 V output from input voltages as low as 3.7 V — well suited for s...

SKU: AF-2324 | Brand: Adafruit

The Adafruit Ultimate GPS HAT adds high-quality GPS and GLONASS positioning to your Raspberry Pi. Built around a PA1616D module, it provides precise location data and a built-in real-time clock (RTC) with coin cell ba...

SKU: AF-2430 | Brand: Adafruit

Pogo pins are little spring-loaded contacts, very handy for making jigs, or making momentary (but electrically solid) contacts. We use them by the dozen for making programming and testing jigs but they're handy also i...

SKU: AF-2442 | Brand: Adafruit

Need to make a tiny robot? This little micro servo rotates 360 degrees fully forward or backwards, instead of moving to a single position. You can use any servo code, hardware or library to control these servos. ...

SKU: DF-FIT0085 | Brand: DFRobot

This custom-designed plastic wheel has a rubber tire measuring 1.65" (42 mm) in diameter and is designed to fit the output shafts on our mini metal gearmotors as well as the Solarbotics metal gear motors. Teeth on...

SKU: DF-SEN0032 | Brand: DFRobot

Breakout board for the Analog Device ADXL345. The ADXL345 is a small, thin, low power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g. Digital output data is formatted as 16-bit twos ...

SKU: DF-FIT0521 | Brand: DFRobot

This is a metal geared DC motor w/Encoder. It is a 6V motor with a 34:1 metal gearbox and an integrated quadrature encoder that provides a resolution of 11 counts per revolution of the motor shaft, which corresponds ...

SKU: DF-FIT0121 | Brand: DFRobot

Jumper wires are one of the most important gear component for the tinkerer. Often underestimated, but one of the first things to miss. If you are starting to assemble your tinker gear and wondering if this is really n...

SKU: AF-2717 | Brand: Adafruit

The TCA9548A 1-to-8 I2C multiplexer solves the common problem of needing multiple I2C devices with the same address on a single bus. It acts as a gatekeeper, routing I2C traffic to any of its eight downstream channels...

SKU: DF-SEN0129 | Brand: DFRobot

INTRODUCTION This is an Arduino CH4 gas sensor. It uses MQ4 probe which is able to detect nature gas, CH4. It is less sensitivity in detecting alcohol, cooking fumes, and cigarette smok...

SKU: SF-BOB-09056 | Brand: SparkFun

A breakout board for the CD74HC4067 16-channel analogue/digital multiplexer/demultiplexer. This IC internally routes a common signal pin (SIG) to one of 16 channel pins, working with both analogue and digital signals ...

SKU: AF-2927 | Brand: Adafruit

A Feather board without ambition is a Feather board without FeatherWings! This is the DC Motor + Stepper FeatherWing which will let you use 2 x bi-polar stepper motors or 4 x brushed DC motors (or 1 ...

SKU: SF-PRT-14017 | Brand: SparkFun

This 2x20 “tall” header has the same number and spacing of pins as a Raspberry Pi and provides your board with the ability to extend the heights of your GPIO to accommodate for enclosures or other parts that can en...

SKU: DF-FIT0314 | Brand: DFRobot

NFC Tag (13.56MHz) is widely used in electronic locks or customer identification as well as other systems where a small and easy to carry tag is desired.The tag contains a NXP S50 chip and an antenna, and is passi...