All Products

SKU: AF-1093 | Brand: Adafruit

Pulse Sensor Amped is a greatly improved version of the original Pulse Sensor, a plug-and-play heart-rate sensor for Arduino and Arduino compatibles. It can be used by students, artists, athletes, makers, and game & m...

SKU: AF-1164 | Brand: Adafruit

This breakout board will solve all your current-monitoring problems. Instead of struggling with a multimeter, you can just use the handy INA169 chip on this breakout to both measure both the DC current draw and have a...

SKU: AF-4062 | Brand: Adafruit

The Feather nRF52840 Express upgrades the nRF52 Bluefruit with the Nordic nRF52840 — featuring 1 MB flash, 256 KB SRAM, native USB, and Bluetooth Low Energy in a single chip. Native USB means no separate serial conver...

SKU: PI-PPMB00130 | Brand: Pimoroni

The Amp:bit is the easiest way to connect a speaker or headphones to your BBC micro:bit. It plugs directly onto the edge connector and provides a 3.5mm headphone jack, solder pads for a speaker, and a volume control w...

SKU: AF-3379 | Brand: Adafruit

The Feather 32u4 Bluefruit LE with Headers combines an ATmega32u4 microcontroller with a Bluetooth Low Energy module, USB connectivity, and LiPo battery charging — with standard headers pre-soldered so you can plug st...

SKU: TB-RN3444 | Brand: Little Bird

A 100 kΩ NTC (Negative Temperature Coefficient) thermistor in a radial dipped-epoxy package. These ceramic sensors change resistance rapidly with temperature, making them ideal for temperature measurement, compensatio...

SKU: AF-1381 | Brand: Adafruit

This breakout board is the ultimate companion for the VLSI VS1053B DSP codec chip. The VS1053 can decode a wide variety of audio formats such as MP3, AAC, Ogg Vorbis, WMA, MIDI, FLAC, WAV (PCM and ADPCM). It can al...

SKU: DF-SEN0232 | Brand: DFRobot

The Gravity Analog Sound Level Meter is an Arduino-compatible decibel meter that accurately measures environmental noise levels. It uses an instrumentation-grade circuit with a low-noise microphone for high-precision ...

SKU: AF-1849 | Brand: Adafruit

Get started with wearable electronics using the Adafruit Gemma Sensor Starter Pack. This all-in-one kit includes a GEMMA V2 board, sewable RGB NeoPixels, multiple sensors, a rechargeable battery with charger, and ever...

SKU: AF-2378 | Brand: Adafruit

The Arduino Pro Mini is SparkFun's minimal design approach to Arduino.  It's essentially a 5v Arduino that runs an 16 MHz bootloader on a super small, super thin board.  There are no connectors attached -...

SKU: AF-2524 | Brand: Adafruit

This high-power RGB LED from Adafruit delivers serious brightness, with each red, green, and blue die capable of handling 350–750mA continuous current (2A peak). At 3W it produces approximately 150 lumens, scaling up ...

SKU: DF-DFR0126 | Brand: DFRobot

This Audio Analyzer module features the MSGEQ7 graphic equalizer display filter.It will give your arduino ears. Sound is broken down into seven frequency bands and the peak level for each band can be read. The seven ...

SKU: PL-2463 | Brand: Pololu

The Vishay TSSP58P38 is a unique modulated IR receiver that is designed for IR brightness detection instead of data communication for remote control. This sensor can be used with a 38 kHz modulated IR emitter an...

SKU: SF-SEN-09198 | Brand: SparkFun

The Minisense 100 from Measurement Specialties is a low-cost cantilever-type vibration sensor loaded by a mass to offer high sensitivity at low frequencies. Useful for detecting vibration and ‘tap’ inputs from a user....

SKU: SF-SEN-09197 | Brand: SparkFun

A flexible piezo vibration sensor from Measurement Specialties, commonly used for detecting flex, touch, vibration, and shock. The PVDF polymer film generates a small AC voltage (up to ±90 V) when it moves, which can ...

SKU: SF-BOB-09110 | Brand: SparkFun

This is the breakout board for the thumb joystick. Pins are broken out to a 0.1" header and includes 4 mounting holes in the corners.

SKU: AF-2771 | Brand: Adafruit

The Feather 32u4 Basic Proto is the no-frills member of the Feather 32u4 family, with a built-in prototyping area where you can solder on extra components like buttons, sensors, or connectors without needing a separat...

SKU: DF-SEN0139 | Brand: DFRobot

This is a K type Thermocouple (Temperature sensor) which is very popular for 3D printers such as Ultimaker and Makerbot. You can hardly damage them or mishandle them. You just need an additional IC (Like an AD595) ...

SKU: SF-DEV-08777 | Brand: SparkFun

Detecting temperature changes has never been easier. The MCP9700 is a small thermistor type temperature sensor. This sensor will output 0.5V at 0 degrees C, 0.75V at 25 C, and 10mV per degree C. Doing an analog to dig...

SKU: SF-SEN-08712 | Brand: SparkFun

This is a piezoresistive force sensor from Tekscan. The harder you press, the lower the sensor’s resistance. Pressing hard, the resistance changes from infinite to ~300k. The sensor itself is thin and flexible, but th...