All Products

SKU: AF-1164 | Brand: Adafruit

This breakout board will solve all your current-monitoring problems. Instead of struggling with a multimeter, you can just use the handy INA169 chip on this breakout to both measure both the DC current draw and have a...

SKU: AF-4062 | Brand: Adafruit

The Feather nRF52840 Express upgrades the nRF52 Bluefruit with the Nordic nRF52840 — featuring 1 MB flash, 256 KB SRAM, native USB, and Bluetooth Low Energy in a single chip. Native USB means no separate serial conver...

SKU: AF-3379 | Brand: Adafruit

The Feather 32u4 Bluefruit LE with Headers combines an ATmega32u4 microcontroller with a Bluetooth Low Energy module, USB connectivity, and LiPo battery charging — with standard headers pre-soldered so you can plug st...

SKU: AF-1381 | Brand: Adafruit

This breakout board is the ultimate companion for the VLSI VS1053B DSP codec chip. The VS1053 can decode a wide variety of audio formats such as MP3, AAC, Ogg Vorbis, WMA, MIDI, FLAC, WAV (PCM and ADPCM). It can al...

SKU: AF-2378 | Brand: Adafruit

The Arduino Pro Mini is SparkFun's minimal design approach to Arduino.  It's essentially a 5v Arduino that runs an 16 MHz bootloader on a super small, super thin board.  There are no connectors attached -...

SKU: DF-DFR0126 | Brand: DFRobot

This Audio Analyzer module features the MSGEQ7 graphic equalizer display filter.It will give your arduino ears. Sound is broken down into seven frequency bands and the peak level for each band can be read. The seven ...

SKU: PL-2463 | Brand: Pololu

The Vishay TSSP58P38 is a unique modulated IR receiver that is designed for IR brightness detection instead of data communication for remote control. This sensor can be used with a 38 kHz modulated IR emitter an...

SKU: SF-SEN-09198 | Brand: SparkFun

The Minisense 100 from Measurement Specialties is a low-cost cantilever-type vibration sensor loaded by a mass to offer high sensitivity at low frequencies. Useful for detecting vibration and ‘tap’ inputs from a user....

SKU: SF-SEN-09197 | Brand: SparkFun

A flexible piezo vibration sensor from Measurement Specialties, commonly used for detecting flex, touch, vibration, and shock. The PVDF polymer film generates a small AC voltage (up to ±90 V) when it moves, which can ...

SKU: SF-DEV-08777 | Brand: SparkFun

Detecting temperature changes has never been easier. The MCP9700 is a small thermistor type temperature sensor. This sensor will output 0.5V at 0 degrees C, 0.75V at 25 C, and 10mV per degree C. Doing an analog to dig...

SKU: AF-334 | Brand: Adafruit

If you've got a resistive touch screen that you'd like to use, you'll need this breakout! It has a fine pitch (0.5mm) connector soldered onto it and it's broken out into the 4 resistive wires of the panel. A petite...

SKU: AF-3246 | Brand: Adafruit

A neat little breakout board designed for mounting a PSP-style mini thumbstick to your project. The board features panel-mount friendly hole placement and dual-sided headers for mechanical stability when connected to ...

SKU: DF-SEN0162 | Brand: DFRobot

The Gravity Analog UV Sensor V2 uses a GUVA-S12SD photodiode to detect ultraviolet radiation in the 200–370 nm (UV-A) wavelength range. It outputs a linear analogue voltage signal proportional to UV intensity, making ...

SKU: SF-COM-10468 | Brand: SparkFun

The MSGEQ7 is a CMOS graphic equaliser IC that divides the audio spectrum into seven frequency bands: 63 Hz, 160 Hz, 400 Hz, 1 kHz, 2.5 kHz, 6.25 kHz, and 16 kHz. Each band is peak-detected and multiplexed to provide ...

SKU: SF-SEN-12642 | Brand: SparkFun

The SparkFun Sound Detector is a small and very easy to use audio sensing board with three different outputs. The Sound Detector not only provides an audio output, but also a binary indication of the presence of so...

SKU: AF-1918 | Brand: Adafruit

An analog UV light sensor breakout based on the GUVA-S12SD photodiode, detecting the 240–370nm range covering UVB and most of the UVA spectrum. An on-board op-amp amplifies the tiny photodiode current to a readable vo...

SKU: SF-SEN-09674 | Brand: SparkFun

This very long force sensitive resistor - over 2 feet - has a sensing area of 0.25x24". This FSR from Interlink Electronics will vary its resistance depending on how much pressure is being applied to the sensing area....

SKU: DF-SEN0203 | Brand: DFRobot

The DFRobot heart rate sensor is a thumb-sized heart rate monitor designed for Arduino microcontrollers. This sensor is a pulse sensor which is developed based on PPG (PhotoPlethysmoGraphy) techniques. This ...

SKU: SF-COM-09542 | Brand: SparkFun

The QRE1113 is a small IR reflectance sensor. This sensor is often used in line following robots because, if it can sense if a surface is white or black. There are four pins on the QRE1113 - two control the IR em...

SKU: AF-333 | Brand: Adafruit

A 4-wire resistive touch screen digitiser (originally designed for the Nintendo DS Lite) that works with a stylus or fingertip. It can be used with any microcontroller that has 2 digital pins and 2 analogue input pins...