All Products

SKU: AF-1362 | Brand: Adafruit

This breakout board is the simplest way to create a project with mutiple capacitive touch sensors. No microcontroller is required here - just power with 1.8 to 5.5VDC and connect up to 5 conductive pads to the 5 left-...

SKU: AF-3721 | Brand: Adafruit

The AM2320 is a low-cost digital temperature and humidity sensor with an I2C interface — a simpler alternative to the classic DHT11/DHT22 sensors that require timing-critical bit-bang protocols. With standard I2C comm...

SKU: SF-SEN-14349 | Brand: SparkFun

This is not your normal Passive Infrared (PIR) sensor! The SparkFun AK9753 Human Presence Sensor Breakout is a Qwiic-enabled, 4-channel Nondispersive Infrared (NDIR) sensor. Each channel has a different field of view...

SKU: SF-COM-08236 | Brand: SparkFun

This is a fully assembled simple breakout board for the surface mount 3-way switch. These switches are commonly found on handheld devices like MP3 players. This switch allows the user to navigate using up and down sel...

SKU: SF-BOB-11040 | Brand: SparkFun

The SparkFun LED RingCoder Breakout provides a visual position indicator for rotary encoders. Two 8-bit shift registers drive a circular LED bargraph that displays the virtual position of the encoder as it turns, givi...

SKU: AF-1727 | Brand: Adafruit

The MAX31850K breakout board is a 1-Wire thermocouple amplifier with cold-junction compensation for K-type thermocouples. Unlike SPI-based amplifiers, the 1-Wire interface allows any number of thermocouple breakouts t...

SKU: AF-1032 | Brand: Adafruit

A gyroscope is a type of sensor that can sense twisting and turning motions. Often paired with an accelerometer, you can use these to do 3D motion capture and inertial measurement (that is - you can tell how an object...

SKU: DF-SEN0005 | Brand: DFRobot

This low cost SFR02 ultrasonic ranger has both I2C and Serial interfaces. New AutoTune algorithms intelligently back the minimum range right up to the transducer ringdown for the very best performance possible, aut...

SKU: DF-TEL0026 | Brand: DFRobot

A Bluetooth 2.0 serial module for Arduino, featuring the CSR BC417143 chip with a double-board design for electrostatic protection. Provides transparent serial data communication over Bluetooth with a configurable bau...

SKU: PL-2454 | Brand: Pololu

The QTR-L-1A reflectance sensor incorporates a right-angle infrared LED and a right-angle phototransistor in an inexpensive, tiny 0.35″ × 0.3″ module that can be mounted almost anywhere and is great for e...

SKU: SF-BOB-09322 | Brand: SparkFun

A simple breakout PCB for the GP1A57HR photo interrupter (also known as a photogate, photodiode, or phototransistor). This PCB has three connections for PWR, GND, and Signal.When the gate is clear, SIG will be high (>...

SKU: AF-466 | Brand: Adafruit

The VCNL4010 sensor is a nice way to add a small-distance proximity sensor to your microcontroller project. For longer distances (in the range of cm, you can use a SHARP IR distance sensor, but those are only good ...

SKU: DF-SEN0140 | Brand: DFRobot

The DFRobot 10 DOF MEMS IMU Sensor combines four sensors on a single compact board — the ADXL345 accelerometer, ITG-3205 gyroscope, HMC5883L magnetometer, and BMP085 barometric pressure sensor. Together they provide 1...

SKU: SF-BOB-12052 | Brand: SparkFun

Odometers are extremely useful for cars, they tell you how far you have gone, wouldn’t it be nice if you were able to have a device that does the same for electrical current? The LTC4150 SparkFun Coulomb Counter Break...

SKU: SF-COM-08348 | Brand: SparkFun

The TEMT6000x01 is a compact ambient light sensor that operates as an NPN phototransistor. The more light that hits the sensor, the stronger the base bias, producing an analog output proportional to the ambient light ...

SKU: SF-SEN-12040 | Brand: SparkFun

The INA169 is a “high-side current monitor,” which means that you place a resistor (a “shunt resistor”) on the positive power rail and the INA169 measures the voltage drop across that resistor. The INA169 outputs a sm...

SKU: DF-FIT0319 | Brand: DFRobot

This is a photoelectric switch that is composed of emitter and receptor.The emitter consists of a laser diode,and the laser has the characteristics of high precision, good orientation etc.The receptor consists of a p...

SKU: SF-SEN-13963 | Brand: SparkFun

The SparkFun LIS3DH breakout is a low-power, three-axis accelerometer with 12-bit resolution, ideal for adding motion and orientation detection to your projects. It communicates over I2C or SPI and includes three addi...

SKU: PL-1268 | Brand: Pololu

The Pololu MinIMU-9 v2 is a compact (0.8″ × 0.5″) board that combines ST’s L3GD20 3-axis gyroscope and LSM303DLHC 3-axis accelerometer and 3-axis magnetometer to form an inertial measurement unit (IMU); we therefore r...

SKU: PL-1265 | Brand: Pololu

This board has been replaced by the newer MinIMU-9 v2 L3GD20 and LSM303DLHC carrier, which offers improved magnetic sensing resolution, a wider acceleration measurement range, and gyro measurements that are more resis...