All Products

SKU: SF-COM-09117 | Brand: SparkFun

This is a 12-step rotary encoder with a nice ‘clicking’ feel. It’s breadboard friendly, and has a pretty handy select switch (by pushing in on the knob). The encoder is different from a potentiometer in that an enc...

SKU: SF-SEN-09088 | Brand: SparkFun

This is a very small light sensor. A photocell changes (also called a photodetector, photo resistor, CdS or photoconductive cell) resistance depending on the amount of light it is exposed to. These little sensors make...

SKU: SF-PRT-12083 | Brand: SparkFun

This 4xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover, which is secured with a small phillips head screw. Another bonus is the ON/OFF swi...

SKU: SF-BOB-14021 | Brand: SparkFun

This is the SparkFun RJ11 Breakout, two simple breakout boards for the common 6-pin RJ11 connector. These little boards can easily have one of our RJ11 6-Pin Connectors to work with common telephone cables. Each bo...

SKU: DF-FIT0244 | Brand: DFRobot

A pack of 50 basic 3mm LEDs in five colours — 10 each of red, green, yellow, white, and blue. Handy for prototyping, indicator lights, and Arduino projects. Specifications Forward Voltage – 1.8–2.2V Max Current – ...

SKU: SF-PRT-08272 | Brand: SparkFun

This 2 mm pitch 10-pin socket mates with XBee radio modules from Digi, allowing you to mount your XBee without soldering it directly to a PCB. You'll need two of these sockets to connect to all 20 pins on an XBee modu...

SKU: DF-FIT0323 | Brand: DFRobot

This 100-piece assortment gives you a handy spread of common through-hole diodes for prototyping, repairs and general project builds. It covers small-signal diodes, standard rectifiers, fast-recovery diodes and Schott...

SKU: SF-COM-00533 | Brand: SparkFun

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very standard red LED. The lens is 3mm in diameter, and is diffused.

SKU: DF-DFR0017 | Brand: DFRobot

The DFRobot Relay Module is a standard relay used with a controller board to interface external electrical circuits or modules. Some of the most common applications with Arduino are: Home lighting, electrical appli...

SKU: SF-COM-11620 | Brand: SparkFun

A compact linear-taper slide potentiometer rated at 10 kΩ and 0.1 W. This small slider features solder tab connections, a 20 mm travel distance, and two mounting holes for easy installation. Key Features Linear Tap...

SKU: DF-DFR0029-R | Brand: DFRobot

Press to release pleasure! Our redesigned digital push buttons come with LED, immersion gold surface, and bright colored hats. A captital D at left corner indicates that it is a digital sensor. An illustration of b...

SKU: AF-161 | Brand: Adafruit

CdS cells are little light sensors. As the squiggly face is exposed to more light, the resistance goes down. When its light, the resistance is about 5-10KΩ, when dark it goes up to 200KΩ. To use, connect one side o...

SKU: AF-239 | Brand: Adafruit

This is a 'full-size' breadboard, 830 tie points. Good for small and medium projects. It's 2.2" x 7" (5.5 cm x 17 cm) with a standard double-strip in the middle and two power rails on both sides. You can pull the powe...

SKU: DF-FIT0365 | Brand: DFRobot

 INTRODUCTION Premium quality jumper wires for prototyping. Made with 26AWG multi-strand wire and sturdy male pins. Each jumper wire is approximately 210mm in length. Each pack comes with 30 jumper wires in a...

SKU: SF-COM-11372 | Brand: SparkFun

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very basic 5mm LED with a blue lens. It has a typical forward voltage of 3.4V and ...

SKU: SF-COM-11121 | Brand: SparkFun

Check out these big 10mm through-hole LEDs! The opaque epoxy package causes these LEDs to have a soft, diffuse glow.Features: 3.0-3.4VDC Forward Voltage 20mA Forward Current 40 degree viewing angle 150-180 MCD output ...

SKU: DF-DFR0296 | Brand: DFRobot

The Bluno Nano combines an Arduino Nano-compatible ATmega328 microcontroller with an integrated TI CC2540 Bluetooth 4.0 (BLE) module in a compact 53 × 19 mm form factor. It enables wireless communication, wireless pro...

SKU: DF-TEL0087 | Brand: DFRobot

Add bluetooth 4.0 to your PC, Mac directly with this USB BLE-Link. It uses the USB package which is compact and compatible with v2.1 and earlier, and also supports the latest v4.0/Bluetooth Low Energy. Now you coul...

SKU: DF-DFR0332 | Brand: DFRobot

Make an air aerial propeller vessel, a cooling system, or spinning machine with this small fan module. It comes with a propeller, a 15,000 rpm motor and cable. Add flavor to your own interesting projects with this ...

SKU: SF-COM-12993 | Brand: SparkFun

This is an SMD 12mm square SPST button. What we really like is the large button head and good tactile feel (it ‘clicks’ really well). This button is great for user input or a good reset button on a PCB, heck, we use t...