Adafruit

SKU: AF-6062 | Brand: Adafruit

The Adafruit INA3221 breakout monitors current, voltage, and power on up to three independent power rails simultaneously over I2C. Each channel supports high or low-side measurement up to +26V DC at ±3.2A with ±1% pre...

SKU: AF-6038 | Brand: Adafruit

The Adafruit SPI Flash SD Card breakout features an XTSD 2 GB chip — an SD card in an SMT package that you can wire up like standard SPI flash but use with existing SD card libraries. It comes pre-formatted as a 2 GB ...

SKU: AF-6004 | Brand: Adafruit

This panel-mount USB extension cable runs a USB Type-A port through an enclosure wall. The socket end has two flexible mounting ears with pre-installed M3 screws for securing to a panel, while the plug end connects to...

SKU: AF-6019 | Brand: Adafruit

DescriptionThis accessory simplifies wiring sensors to your Bus Pirate 5, featuring snap-open quick connects that easily plug into the BP5’s header port. When you’re ready to dive into a project, these quick connecto...

SKU: AF-6021 | Brand: Adafruit

The Bus Pirate 5 SOIC/SOP8 SPI Flash Adapter makes it easy to program bare SPI flash memory chips without clips or soldering. The spring-loaded ZIF socket accepts SOP8 packages in both 150 mil and 208 mil widths — the...

SKU: AF-6015 | Brand: Adafruit

Here is a cute and minimal enclosure for your TRRS Trinkey to keep it safe during use and transport. This case has been custom-designed and 3D printed to accommodate the reset button and STEMMA QT connector. No screws...

SKU: AF-6003 | Brand: Adafruit

The Adafruit Metro RP2350 brings the next-generation Raspberry Pi RP2350 dual-core processor to the standard Metro/UNO shield-compatible form factor. With dual ARM Cortex-M33 cores running at 150 MHz, 528 KB SRAM, 16 ...

SKU: AF-6002 | Brand: Adafruit

Here is a cute and minimal enclosure for your QT Py to keep it safe during use and transport. This case has been custom-designed and 3D printed to accommodate the USB-C connector. No screws or glue are required; simpl...

SKU: AF-5999 | Brand: Adafruit

The Adafruit CH334F Mini 2-Port USB Hub Breakout converts one USB host port into two downstream ports using the CH334F USB 2.1 hub chip. Designed to be compact and embeddable, it fits inside enclosures or existing dev...

SKU: AF-5998 | Brand: Adafruit

Here is a cute and minimal enclosure for your Pixel Trinkey to keep it safe during use and transport. This case has been custom-designed and 3D printed to accommodate the reset button, 3-pin JST SH port, and the 4 ter...

SKU: AF-5988 | Brand: Adafruit

The Adafruit RS-232 Full Pinout Level-Shifter Breakout lets you interface any 3.3 V microcontroller or single-board computer with RS-232 devices using all 8 data/flow-control signals. Built around the trusted TI MAX32...

SKU: AF-6001 | Brand: Adafruit

The Adafruit Reversible USB Type A Plug Connector Breakout breaks out a reversible USB Type A plug to breadboard-friendly pins. The connector uses a thin centre contact so it can be plugged in either way — no more gue...

SKU: AF-5996 | Brand: Adafruit

The Adafruit QT Py CH32V203 is a tiny development board built around the WCH CH32V203G6 — a low-cost RISC-V microcontroller running at up to 144 MHz. In the compact QT Py form factor (Seeed Xiao compatible), it packs ...

SKU: AF-5991 | Brand: Adafruit

The Adafruit USB Type C Power Delivery Dummy (I2C or Switchable) lets you tap into USB-C Power Delivery to get 5V, 9V, 12V, 15V, 18V, or 20V from any compatible USB-C charger or wall adapter — no soldering required. B...

SKU: AF-5981 | Brand: Adafruit

Here is a cute and minimal enclosure for your TRRS Trinkey to keep it safe during use and transport. This case has been custom designed and 3D printed to accommodate the reset button and STEMMA QT connector. No screws...

SKU: AF-5974 | Brand: Adafruit

The Adafruit HX711 Breakout is a high-resolution 24-bit differential ADC designed for reading load cells, strain gauges, and other Wheatstone bridge sensors. With selectable 64× or 128× gain on Channel A and fixed 32×...

SKU: AF-5976 | Brand: Adafruit

The Adafruit DS2484 is a single-channel I2C-to-1-Wire bus adapter breakout with built-in ESD protection and split supply support. Simply connect it to an existing I2C bus and use the screw terminals to attach DS18B20 ...

SKU: AF-5972 | Brand: Adafruit

The Adafruit Switchable USB Type A to C Breakout Board lets you individually enable or disable each of the four USB wires (V+, D+, D−, GND) using an onboard 4-position DIP switch. This makes it a versatile tool for US...

SKU: AF-5970 | Brand: Adafruit

The Adafruit TSMP96000 "Code Learning" Infrared IR Receiver Breakout detects IR signals across a wide frequency range of 20–60 KHz, making it perfect for "code learning" applications where you need your device to work...

SKU: AF-5929 | Brand: Adafruit

MAJOR KEY ALERT 🔑🔑🔑 we now stock 'Key Lock Switches'! These mechanical switches don't use a button, a lever, or a magnet to open and close the contacts. Instead, a literal key is used. This low-cost but effective key...