Adafruit

SKU: AF-1713 | Brand: Adafruit

Add an ear to your project with this well-designed electret microphone amplifier with AGC. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, we use th...

SKU: AF-1463 | Brand: Adafruit

Round and round they go! 16 ultra-bright smart RGB NeoPixels are arranged in a circle with a 44.5 mm (1.75″) outer diameter. Each LED is individually addressable from a single microcontroller pin, delivering 24-bit co...

SKU: AF-2310 | Brand: Adafruit

The Adafruit Perma-Proto HAT for Pi Mini Kit is a full-sized prototyping daughter board for any Raspberry Pi with a 2×20 GPIO header (Pi Zero, A+, B+, Pi 2, 3, 4, 5). It provides a grid of 0.1″ soldering holes connect...

SKU: AF-2167 | Brand: Adafruit

Infrared (IR) break-beam sensors are a simple way to detect motion. They work by having an emitter side that sends out a beam of human-invisible IR light, then a receiver across the way which is sensitive to tha...

SKU: AF-3082 | Brand: Adafruit

A tall-profile aluminium heatsink with pre-applied thermal adhesive for easy installation on the Raspberry Pi 3 and other single board computers. The taller 15mm height provides greater surface area for improved heat ...

SKU: AF-367 | Brand: Adafruit

Little clicky switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a solderless breadboard as shown in this tutorial. The pins are normally open (disconnected) a...

SKU: AF-413 | Brand: Adafruit

Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This mak...

SKU: AF-746 | Brand: Adafruit

The Adafruit Ultimate GPS Breakout (Version 3) is a high-performance GPS module built around the MTK3339 chipset. With 66 channels, -165 dBm tracking sensitivity, and up to 10 Hz position updates, it delivers accurate...

SKU: AF-4714 | Brand: Adafruit

We use 2 pin JST PH connectors for all our battery packs, and if you want to put a board in series, like our LC709203F Stemma QT battery gauge, this cable will be very handy! Both ends have a JST PH 2mm pitch 2-pin...

SKU: AF-5616 | Brand: Adafruit

A lever-action wiring block connector with one input and five outputs, ideal for quick power or signal fan-outs without soldering, crimping, or tools. Snap the lever open, insert the wire, and snap it closed for a sec...

SKU: AF-5113 | Brand: Adafruit

Kailh Choc Low Profile Red linear mechanical key switches in a pack of 10. These ultra-low-profile switches are significantly thinner than standard MX-style switches, making them ideal for slim custom keyboards and co...

SKU: AF-4890 | Brand: Adafruit

Need to measure something with a very slim sensor? This precision 10K thermistor is an inexpensive way to measure temperature in a small gap, or taped to a flat surface, it's only 0.2mm wide!The resistance in 25°C is ...

SKU: AF-4456 | Brand: Adafruit

A 0.8mm-wide copper desoldering wick for removing excess solder from PCB pads and joints. The narrow width makes it particularly suited for surface-mount (SMT) work, where precision is essential. Place the wick over t...

SKU: AF-4256 | Brand: Adafruit

Wanna improve the connection strength between your project's 3D-printed parts, and also have nice clean surfaces? Instead of gluing bits together, or screwing plastic screws directly into your 3D prints, use strong an...

SKU: AF-3960 | Brand: Adafruit

With our fun assortment of conductive materials, cosplay and wearables have never been easier to craft!  This Conductive Nylon tape goes great with our other interesting materials, such as copper tape, ITO gl...

SKU: AF-2226 | Brand: Adafruit

Be the belle of the ball with the NeoPixel Jewel!  We fit seven of our tiny 5050 (5mm x 5mm) smart RGB LEDs onto a beautiful, round PCB with mounting holes and a chainable design to create what we think...

SKU: AF-900 | Brand: Adafruit

A short USB 2.0 Type-A to Type-B cable, 150 mm (6") in length. Ideal for connecting Arduino boards, programmers, and other USB-B devices to a computer in compact setups where a full-length cable is unnecessary. Key F...

SKU: AF-1012 | Brand: Adafruit

Make your Internet of Things device cable-free by adding WiFi. Take advantage of the Raspberry Pi and Beagle Bone's USB port to add a low cost, but high-reliability wireless link. We tried half a dozen modules to f...

SKU: AF-1192 | Brand: Adafruit

BAM! This 60mm diameter arcade button is large and inviting and ready for all sorts of pressing and pushing. We've seen these on some games of skill in arcades, they're easy to mount on nearly any kind of enclosure. T...

SKU: AF-1188 | Brand: Adafruit

OMG WATCH OUT! This 100mm diameter arcade button with a 16mm deep plastic base is so massive and inviting it may collapse upon itself and form a black hole from which not even light can escape! Until it does, how...