Adafruit

SKU: AF-3287 | Brand: Adafruit

A compact 3×AA battery holder with a built-in on/off switch, JST 2-pin connector, and an ergonomic belt clip. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making...

SKU: AF-1903 | Brand: Adafruit

The PowerBoost 500 Basic is a compact DC/DC boost converter that takes input from 1.8V or higher and outputs a steady 5.2V — perfect for powering portable 5V projects from batteries. The slightly elevated 5.2V output ...

SKU: AF-3428 | Brand: Adafruit

A voltage detector is handy for projects where you want to make sure your microcontroller doesn't run at a low voltage. For example, say you have a Feather Huzzah running on a lipoly battery every few minutes. Even...

SKU: AF-5580 | Brand: Adafruit

The Adafruit MAX17048 LiPoly/LiIon Fuel Gauge and Battery Monitor gives you accurate battery voltage and charge percentage readings for your 1S 3.7–4.2V lithium polymer or lithium ion battery. Instead of guessing rema...

SKU: AF-5704 | Brand: Adafruit

The Witty Pi 4 is a Raspberry Pi HAT that adds a precision real-time clock, power management, and scheduling capabilities. Define ON/OFF sequences to significantly reduce energy usage in battery-powered systems, or us...

SKU: AF-6349 | Brand: Adafruit

The Adafruit INA238 is a precision DC power monitor capable of measuring current, voltage, and power on either the high or low side of your circuit. With support for up to +85V DC common-mode voltage and a 16-bit ADC,...

SKU: AF-6340 | Brand: Adafruit

The Adafruit INA237 is a precision DC power monitor capable of measuring current, voltage, and power on either the high or low side of your circuit. With support for up to +85V DC common-mode voltage and a 16-bit ADC,...

SKU: AF-5991 | Brand: Adafruit

The Adafruit USB Type C Power Delivery Dummy (I2C or Switchable) lets you tap into USB-C Power Delivery to get 5V, 9V, 12V, 15V, 18V, or 20V from any compatible USB-C charger or wall adapter — no soldering required. B...

SKU: AF-5882 | Brand: Adafruit

The Adafruit DC Power BFF Add-On lets you power your QT Py or Xiao development board from a DC source up to 20V. The on-board MPM3610 integrated buck converter steps down the input to 5V at up to 1A, with no heat sink...

SKU: AF-3546 | Brand: Adafruit

A passive adapter with a 1st-generation MagSafe plug on one end and a 5.5 mm / 2.1 mm DC barrel jack (centre-positive) on the other. It lets you connect a 15–20 VDC barrel-jack power supply to devices that use the ori...

SKU: AF-3573 | Brand: Adafruit

The Adafruit TPL5111 Low Power Timer Breakout turns any electronics project into a low-power system by periodically toggling an enable pin. Connect it to your project's enable line, and the TPL5111 will handle the res...

SKU: AF-3848 | Brand: Adafruit

An isolated Power over Ethernet (PoE) module that extracts power from the Ethernet cable's centre taps and outputs a regulated 5 V at up to 1.8 A. The built-in isolation transformer ensures there is no direct electric...

SKU: AF-3847 | Brand: Adafruit

A compact Power over Ethernet (PoE) module that extracts power from the Ethernet cable's centre taps and outputs a regulated 5 V at up to 1.5 A. Connect the four input wires to the PoE pins on your Ethernet-capable bo...

SKU: AF-3788 | Brand: Adafruit

A 4×AA battery holder with a built-in on/off switch and a 13cm (5″) power cable terminating in a centre-positive 2.1mm DC barrel jack. Provides convenient portable power with easy switching for development boards and ...

SKU: AF-3624 | Brand: Adafruit

This Mini Power Meter with Voltage, Current, Watts, mAh & mWh Display (whew that is a mouth-full) is a lot like the USB In-Line Voltage and Current Meter we carry but can  be used with a wide range of voltages...

SKU: AF-3650 | Brand: Adafruit

The Adafruit INA219 FeatherWing is a high-side current and voltage sensor that stacks onto any Feather development board. Using the INA219B chip over I2C, it measures both DC current draw and bus voltage with 1% preci...

SKU: AF-1335 | Brand: Adafruit

This is for people who just want to get cold fast. The 12V Peltier module is mounted onto a 12V heatsink and fan assembly with thermal paste and an aluminum clamp. Simply connect to 12V 5A+ power supply and you will s...

SKU: AF-1350 | Brand: Adafruit

A really tiny portable inverter for EL wire. Powers off of a single CR2032 coin battery (not included!), it can drive up to 50cm / 20 inches of our high-brightness EL wire or 10cm x 1cm long piece of EL tape for 3 ...

SKU: AF-1352 | Brand: Adafruit

A simple 1-to-4 DC barrel jack splitter that lets you power four devices from a single DC power adapter. Features standard 5.5mm/2.1mm barrel connectors with rugged moulded construction. Plug your existing DC power s...

SKU: AF-1407 | Brand: Adafruit

The squarish board with two chips on it is the transmitter (power with 9V).  The longer board is the output and you can connect that to the part of your project that needs powering. Inductive charging ...