Adafruit

SKU: AF-3661 | Brand: Adafruit

The Adafruit MiniBoost is a tiny charge-pump voltage booster that converts 3–5 V input to a regulated 5 V output at up to 100 mA. About the size of a linear regulator, it's an easy drop-in solution for battery-powered...

SKU: AF-1459 | Brand: Adafruit

This inductive charging set provides wireless power transfer using a split-transformer design. The transmitter coil is powered with 9–12 V DC, and the receiver coil outputs 3.3 V DC — no direct wire connection between...

SKU: AF-1570 | Brand: Adafruit

A compact 3.7 V lithium-ion polymer (LiPo) battery with approximately 100 mAh capacity (0.4 Wh). Thin, lightweight, and powerful, this cell is suited for small wearable projects, IoT devices, and compact electronics w...

SKU: AF-1794 | Brand: Adafruit

When you need to switch a lot of power, P channel MOSFETs are best for the job. These P-FETs can switch over 60V and 25A (with proper heat-sinking) and are TO-220 package so they fit nicely into any breadboard or perf...

SKU: AF-1870 | Brand: Adafruit

A simple sewable breakout board with a CR2032 coin cell battery holder pre-soldered on and 0.1" pitch breakout pins for easy connection. Ideal for powering very low-current projects or adding a battery backup circuit ...

SKU: AF-2124 | Brand: Adafruit

The Adafruit Pro Trinket LiIon/LiPoly Backpack is a tiny add-on board that sits on top of your Pro Trinket or ItsyBitsy, adding rechargeable LiPo battery support with automatic charging and power switching. When USB i...

SKU: AF-248 | Brand: Adafruit

A 6×AA battery holder with a 5.5mm/2.1mm DC barrel plug, ready to power Arduino boards and other electronics with a standard DC jack. Use alkaline AAs for approximately 9V at 3000–4000mAh, or rechargeable NiMH cells f...

SKU: AF-3238 | Brand: Adafruit

This IEEE 802.3af PoE splitter separates power and data from a single PoE Ethernet cable, providing regulated 12VDC at up to 1A on a standard 2.1 mm DC barrel jack alongside a standard Ethernet data connection. It let...

SKU: AF-3286 | Brand: Adafruit

A slim 3×AAA battery holder with a built-in on/off switch, JST 2-pin connector, and an ergonomic belt clip. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making i...

SKU: AF-3287 | Brand: Adafruit

A compact 3×AA battery holder with a built-in on/off switch, JST 2-pin connector, and an ergonomic belt clip. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making...

SKU: AF-1903 | Brand: Adafruit

The PowerBoost 500 Basic is a compact DC/DC boost converter that takes input from 1.8V or higher and outputs a steady 5.2V — perfect for powering portable 5V projects from batteries. The slightly elevated 5.2V output ...

SKU: AF-3428 | Brand: Adafruit

A voltage detector is handy for projects where you want to make sure your microcontroller doesn't run at a low voltage. For example, say you have a Feather Huzzah running on a lipoly battery every few minutes. Even...

SKU: AF-5580 | Brand: Adafruit

The Adafruit MAX17048 LiPoly/LiIon Fuel Gauge and Battery Monitor gives you accurate battery voltage and charge percentage readings for your 1S 3.7–4.2V lithium polymer or lithium ion battery. Instead of guessing rema...

SKU: AF-6349 | Brand: Adafruit

The Adafruit INA238 is a precision DC power monitor capable of measuring current, voltage, and power on either the high or low side of your circuit. With support for up to +85V DC common-mode voltage and a 16-bit ADC,...

SKU: AF-6340 | Brand: Adafruit

The Adafruit INA237 is a precision DC power monitor capable of measuring current, voltage, and power on either the high or low side of your circuit. With support for up to +85V DC common-mode voltage and a 16-bit ADC,...

SKU: AF-5991 | Brand: Adafruit

The Adafruit USB Type C Power Delivery Dummy (I2C or Switchable) lets you tap into USB-C Power Delivery to get 5V, 9V, 12V, 15V, 18V, or 20V from any compatible USB-C charger or wall adapter — no soldering required. B...

SKU: AF-5882 | Brand: Adafruit

The Adafruit DC Power BFF Add-On lets you power your QT Py or Xiao development board from a DC source up to 20V. The on-board MPM3610 integrated buck converter steps down the input to 5V at up to 1A, with no heat sink...

SKU: AF-3546 | Brand: Adafruit

A passive adapter with a 1st-generation MagSafe plug on one end and a 5.5 mm / 2.1 mm DC barrel jack (centre-positive) on the other. It lets you connect a 15–20 VDC barrel-jack power supply to devices that use the ori...

SKU: AF-3573 | Brand: Adafruit

The Adafruit TPL5111 Low Power Timer Breakout turns any electronics project into a low-power system by periodically toggling an enable pin. Connect it to your project's enable line, and the TPL5111 will handle the res...

SKU: AF-3848 | Brand: Adafruit

An isolated Power over Ethernet (PoE) module that extracts power from the Ethernet cable's centre taps and outputs a regulated 5 V at up to 1.8 A. The built-in isolation transformer ensures there is no direct electric...