All Products

SKU: LB-LR0296

A 9V battery clip adapter with a standard 5.5 × 2.1 mm centre-positive barrel jack. Use it to power any device that accepts 9V input through an onboard barrel jack connector. Key Features 9V Battery Snap – Standard clip fits all 9V batteries Barrel Jack Output – 5.5 × 2.1 mm centre-positive c...

SKU: AF-255 · MPN: 255

THIS IS THE LATEST VERSION 2.1The ChronoDot RTC is an extremely accurate real time clock module, based on the DS3231 temperature compensated RTC (TCXO). It includes a CR1632 battery, which should last at least 8 years if the I2C interface is only used while the device has 5V power available. No e...

SKU: LB-LR0309-16

A flat 4×AA battery holder with a 2.1mm DC barrel jack connector, providing an easy way to power Arduino boards and other projects that accept a DC barrel plug. With four alkaline AA batteries installed, it delivers approximately 6V — within the recommended input voltage range for the Arduino Uno...

SKU: AF-1862 · MPN: 1862

A simple 2-pin connector soldered onto a breadboard-friendly breakout. This is compatible with the "JST PH 2-pin" connector. Mates perfectly with all our 1-cell LiPoly and LiIon batteries as well as our 6V coin cell holder and 3xAAA battery pack. We also have simple JST pigtails that mate w...

SKU: DF-FIT0080

A 4-cell AA battery holder in a square (2×2) configuration with a sliding removable cover and a built-in ON/OFF switch. Features 5-inch tinned leads for easy soldering. The cover keeps batteries secure, and the switch provides convenient power control without disconnecting wires. Specifications ...

SKU: LB-LR0309-20

A simple single-slot 9V battery holder case with wire leads for soldering or connecting directly to your projects. Keeps your battery secure and organised. Key Features Wire Leads – Pre-attached cables for direct soldering or breadboard connection Snap-Fit Design – Holds one standard 9V batte...

SKU: SF-PRT-00091

A classic 9V battery snap connector terminated with a 2-pin polarised Molex connector. Ideal for quick-connect battery power in breadboard and prototyping setups. Key Features Molex Terminated – 2-pin polarised connector for secure, reversible connections Cable Length – 5 inches (approximatel...

SKU: AF-1868 · MPN: 1868

A simple breakout board with a CR1220 coin cell battery holder pre-soldered and broken out to 0.1″ pitch pins. Ideal for powering very low-current projects or providing battery backup for a real-time clock (RTC) module. Comes fully assembled and tested, with a stick of 0.1″ header included so yo...

SKU: PI-COM1304

A 4×AA battery holder with press-stud (snap) termination, providing a portable power source for wearable and on-the-go projects. With four alkaline AA batteries, it delivers approximately 6V with 7,000–10,000 mAh of capacity — enough to power an Arduino Uno for over a week. Rechargeable NiMH bat...

SKU: AF-1867 · MPN: 1867

A breakout board with a CR1220 coin cell battery holder, an on/off switch, and 0.1″ pitch breakout pins. Ideal for powering very low-current projects or providing switchable battery backup for a real-time clock (RTC) module. The board breaks out four pins: two ground pins, one switched power pin...

SKU: AF-4194 · MPN: 4194

A slim, open-top 2×AA battery holder with a genuine JST PH connector. Two AA batteries in series provide approximately 3V — ideal for powering low-voltage electronics projects, Adafruit boards, and microcontrollers with JST PH battery inputs. The JST PH connector polarity matches Adafruit's Li-I...

SKU: SS-106990021

The 5V/3.3V Breadboard Power Supply plugs directly into a standard breadboard and provides regulated 5V or 3.3V power to both rails. It accepts power via either a 7–15V DC barrel jack or a 5V Micro-USB input, giving you flexible options for powering your prototyping projects. Designed by Seeed S...

SKU: DF-FIT0362

This battery holder takes three AA cells and provides a simple way to power compatible Arduino-style boards via a Micro USB connection.Use it with NiMH or NiCd rechargeable cells for a 3.6V battery pack, or with alkaline cells for a 4.5V battery pack. The holder is made from plastic and includes ...

SKU: DF-FIT0538 · MPN: FIT0538

This battery holder takes two 18650 lithium cells and connects them internally in series for a standard 7.4 V output. It is a simple way to power electronics projects from common 18650 cells, such as those used in laptop battery packs and power banks.The holder includes a DC 2.1 power jack, makin...

SKU: DF-SEN0693 · MPN: SEN0693

Built around the Bosch BMI323, this compact Fermion module combines a 3-axis accelerometer and a 3-axis gyroscope on a 16 mm × 16 mm board. It provides high-rate acceleration and angular velocity data over I²C for embedded motion sensing, wearables, robotics, battery-powered IoT nodes and compact...

SKU: AF-3784 · MPN: 3784

A 4×AA battery holder with a 20cm (8″) power cable terminating in a centre-positive 2.1mm DC barrel jack. Provides a portable power source for development boards and projects that accept a standard DC barrel jack input. Delivers approximately 4.8V with NiMH rechargeable batteries or up to 6V wit...

SKU: LB-LR0309-18

A single-cell 18650 battery holder with bare wire leads, designed for easy integration of 18650 lithium-ion cells into your electronics projects. Simply drop in a battery and connect the leads — no soldering or connectors required. Key Features Single 18650 Cell – Holds one standard 18650 batt...

SKU: DF-FIT0078

A double-layer 6×AA battery holder with a stacked 3+3 cell arrangement for a more compact footprint. Creates a 7.2V rechargeable battery pack from NiMH/NiCd cells or a 9V pack from alkaline cells. Comes with 150mm (6") red and black wire leads. Specifications Cell Quantity: 6× AA (double layer...

SKU: LB-LR0249

Note: These breadboards have a badly laid out silkscreen. They work perfectly well as breadboards, but do not rely on the printed reference markers. An 830-point solderless breadboard (MB-102) at a discounted price. Despite the cosmetic silkscreen issue, the electrical contacts and functionali...

SKU: SF-COM-30154 · MPN: COM-30154

This is a basic 1 MOhms through-hole resistor with ±5% tolerance and a 1/6W power rating. It is a simple passive component suited to prototyping, repairs and general circuit building.The PTH package is commonly used with solderless breadboards, perf boards and other through-hole projects. It is s...