All Products

SKU: AF-4028 · MPN: 4028

Get started with CircuitPython using this all-in-one starter kit built around the Adafruit ItsyBitsy M4 Express. The ItsyBitsy M4 packs a 120 MHz ATSAMD51 Cortex M4 processor with floating point support, 512 KB flash, and 192 KB RAM into a compact, breadboard-friendly form factor — more than enou...

SKU: SS-101060001

Circuit Stickers are electronic stickers that you can use to build glowing, sensing, and interactive projects without any complicated equipment or programming skills. All you need is your imagination.   And this is an add-on sticker kit for Circuit Sticker Starter kit, with sound se...

SKU: CB-0799439675377

Four effects stickers so you can add blink, fade, twinkle and heartbeat effects to your projects!

SKU: CB-SENSOR

Sensors Stickers include a light sensor, a microphone sensor for detecting sound, and a timer circuit that turns on your circuit for five seconds at a time.

SKU: CT-ROAD

We went back to the drawing-board and re-engineered our favorite tape! How did we make it better? We made it out of paper instead of plastic! Now it's: * Easier to remove! Sticks to most surfaces, easy to reposition and remove without any sticky residue.* Wider! 2-3/4 inches of road.&nbsp...

SKU: LB-LS0221

The CJMCU-226 INA226 is a powerful voltage, current, and power monitoring module designed for high precision in both high-side and low-side sensing applications. With its bi-directional current sensing capability and wide operating range, this module is perfect for a variety of applications, incl...

SKU: AF-4675 · MPN: 4675

A clear acrylic enclosure designed specifically for the Adafruit CLUE board. Laser-cut to accommodate the TFT display, tactile buttons, and capacitive pads, this minimalist case protects your board while keeping all features accessible. Assembly takes less than five minutes with the included nyl...

SKU: AF-4013 · MPN: 4013

A laser-cut clear acrylic lens holder with mounting hardware, designed specifically for the Adafruit HalloWing. It holds a lip-edge convex lens (glass or plastic) in front of the HalloWing's display, creating an eye-catching magnified effect for animated eye projects and wearable displays. Assem...

SKU: WS-20550

A clear acrylic protection case designed specifically for the Raspberry Pi Pico. The dual-sided design shields both the top and bottom of your Pico board from scratches, dust, and accidental short circuits while keeping the board fully visible. The case features clear acrylic panels with a neat,...

SKU: AF-4330 · MPN: 4330

Here is the perfect kit for mounting convex lenses (glass or plastic) to your Monster M4sk! These acrylics has been laser-cut specifically for lenses with a lip-edge, so we can't guarantee it'll fit with any ol' convex lens. But it does work great with ours. And of course, the mounting hardware i...

SKU: EF-EF11085

A clear battery holder designed for the BBC micro:bit, holding two AAA batteries. Features a built-in on/off switch and a PH2.0 connector that plugs directly into the micro:bit's battery port. The transparent casing lets you see the batteries inside. Specifications Battery Type – 2× AAA (not i...

SKU: AF-3597 · MPN: 3597

This simple but effective enclosure will fit any 'classic Arduino' shaped development board - we've tested it for sure with the Arduino UNO R3, Adafruit Metro and Adafruit Metro Express. It's clear so you can see all your onboard LEDs and silkscreen labels. There are four small screws you ca...

SKU: AF-5068 · MPN: 5068

A 12-pack of clear DSA keycaps for Cherry MX and compatible switches. The transparent design allows RGB backlighting to shine through clearly, making them ideal for custom keyboards, NeoKey projects, and macro pads where per-key lighting matters. DSA profile keycaps are fully symmetric in all fo...

SKU: AF-5676

Add a splash of clarity to your synth, control panel, or electronics project with these clear micro potentiometer knobs. Made from hard plastic with a grippy star shape (sometimes referred to as "Davies 1900" style), they fit securely on any shaft type. Each knob works with round, D-shaft, or T1...

SKU: AF-315 · MPN: 315

These clear 5 mm Piranha (super-flux) LEDs contain separate red, green, and blue chips in a single square package, allowing full RGB colour mixing. With an 80° viewing angle and a combined brightness of up to 2000 mcd, they work well as indicators, illuminators, or colour-swirl effects. The squar...

SKU: AF-5083 · MPN: 5083

Back in my day, if you wanted a mechanical keyboard, you had to purchase a massive IBM Model M Keyboard but now you can DIY your very own compact keyboards with your very favorite layouts to make the keeb of your dreams.For all the DIY keebfans in the house here is a&nbsp...

SKU: AF-5085 · MPN: 5085

Back in my day, if you wanted a mechanical keyboard, you had to purchase a massive IBM Model M Keyboard but now you can DIY your very own compact keyboards with your very favorite layouts to make the keeb of your dreams.For all the DIY keebfans in the house here is a&nbsp...

SKU: SF-COM-10597

This plastic knob accepts a 6mm shaft and has a 15mm outer diameter. They simple press-fit onto a shaft. These are clear so that they can be used with our illuminated rotary encoders. Documents: Dimensional Drawing

SKU: LB-LS0433

This ABS Transparent Case is designed for Raspberry Pi Zero/ Zero W. There is a large connecting hole for its GPIO and camera port. In addition, the connecting graph of Raspberry Pi’s GPIO 40Pin has been printed on the product’s cover to make it convenient for your connection. This simply desi...

SKU: AF-6015

Here is a cute and minimal enclosure for your TRRS Trinkey to keep it safe during use and transport. This case has been custom-designed and 3D printed to accommodate the reset button and STEMMA QT connector. No screws or glue are required; simply snap the two pieces together over the Trinkey.It's...