All Products

SKU: LB-LS6460

A battery box with a built-in 130 DC motor and on/off switch — a simple, self-contained power and drive unit for beginner robotics, model vehicles, and STEM projects. Just add batteries and connect to your build. Specifications Motor – 130 DC motor Voltage – 3–6 V (depending on battery config...

SKU: EF-EF11085

A clear battery holder designed for the BBC micro:bit, holding two AAA batteries. Features a built-in on/off switch and a PH2.0 connector that plugs directly into the micro:bit's battery port. The transparent casing lets you see the batteries inside. Specifications Battery Type – 2× AAA (not i...

SKU: AF-770 · MPN: 770

Keep your power source safe and toasty in these waterproof 2xAA battery holders. They're just like classic switched battery holders, but designed for survival! The case has a rubber gasket around the edge of the case (its black and hard to see in the photos but it is there) and attaches togeth...

SKU: LB-LS0821

This battery enclosure (with switch) for the BBC micro:bit is the perfect way to power your micro:bit on the go. Specifications:  2x AAA Battery Enclosure Cable Length: ~14cm JST Cable Connector (compatible with the BBC micro:bit power connector). Dimensions: 6.5cm x 2.8cm

SKU: AF-771 · MPN: 771

Keep your power source safe and toasty in these waterproof 3xAA battery holders. They're just like classic switched battery holders, but designed for survival! The case has a rubber gasket around the edge of the case (its black and hard to see in the photos but it is there) and attaches togeth...

SKU: AF-1867 · MPN: 1867

A breakout board with a CR1220 coin cell battery holder, an on/off switch, and 0.1″ pitch breakout pins. Ideal for powering very low-current projects or providing switchable battery backup for a real-time clock (RTC) module. The board breaks out four pins: two ground pins, one switched power pin...

SKU: AF-1863 · MPN: 1863

This switched JST connector is the best way to quickly prototype with our LiPoly batteries. We paired a genuine JST connector with a slide switch that can do up to 600mA. Both are soldered onto a breadboard-friendly breakout. There's two ground pins, one 'switched' power pin, and one pin that ...

SKU: PR-PIM688

A high-power modular robotics and engineering platform, built around RP2040 and designed to drive the most ambitious robots, props and devices. The Do-Everything Board 🦾 Yukon is a standalone controller that can be equipped with up to six interchangeable modules capable of driving high-powe...

SKU: LB-LS1812

Sick of your batteries all floating around in a drawer or box, and then when you come to use them, most are already flat.This had box keeps all your batteries standing upright and has a battery test to show if the battery still has charge.It has space for  45x AA batteries 25x AAA batteries ...

SKU: DF-MBT0005

Micro: IO-BOX is a micro:bit multifunctional expansion board with on-board Li-ion battery power, delicate appearance and easy to use. We integrated numerous functions on the 6cm×6cm board such as 2-way driver motor, 9-way IO port, 2-way I2C port, 1-way serial port, 1-way buzzer, 4-way RGB LED, Li...

SKU: WS-27670 · MPN: 27670

The PoE HAT (G) is an IEEE 802.3af/at-compliant PoE (Power Over Ethernet) HAT for Raspberry Pi 5 / CM 5. By using with a PoE router or switch that supports the IEEE 802.3af/at network standard, it is possible to provide both network connection and power supply for your Raspberry Pi...

SKU: DF-MBT0046

This classroom-ready robot platform is built to make micro:bit STEM lessons smoother, with line tracking, obstacle avoidance, lighting effects and expansion options in a compact robot car format.The Maqueen Lite V5 arrives fully assembled with its motors, battery box and wheels already installed,...

SKU: AF-1870 · MPN: 1870

A simple sewable breakout board with a CR2032 coin cell battery holder pre-soldered on and 0.1" pitch breakout pins for easy connection. Ideal for powering very low-current projects or adding a battery backup circuit to a real-time clock or similar module. Key Features CR2032 Coin Cell Holder ...

SKU: EF-EF09001

Smart Car Chassis  4WD V4 DoubleInstallation Guide please read : https://www.elecfreaks.com/4006.htmlParameters:Wheels: Φ 6cmBottom: thickness of about 3 mmLength: about 25.3cmWidth: about 14.8cmShipping List:Part Name  (Quantity)4WD V1 smart car floor (2)M3-30 flat head hex studs TZ M3...

SKU: DF-MBT0021-EN-18650

Maqueen Plus V2 is a STEAM educational robot platform for the micro:bit, made for classroom teaching, after-school projects and robot competitions. It builds on Maqueen Lite and earlier Maqueen Plus robots with a larger body, more expansion options and a choice of AA or 18650 power versions.The r...

SKU: AF-255 · MPN: 255

THIS IS THE LATEST VERSION 2.1The ChronoDot RTC is an extremely accurate real time clock module, based on the DS3231 temperature compensated RTC (TCXO). It includes a CR1632 battery, which should last at least 8 years if the I2C interface is only used while the device has 5V power available. No e...

SKU: SF-COM-13015

A solid state relay (SSR) allows you to control high-curent AC loads from lower voltage DC control circuitry. Solid state relays have several advantages over mechanical relays. One such advantage is that they can be switched by a much lower voltage and at a much lower current than most mechanical...

SKU: DF-MBT0021-EN-4 · MPN: MBT0021-EN-4

This DFRobot bundle brings together the micro:Maqueen Plus V2 AA robot platform, the micro:Maqueen Mechanic kit and a micro:bit V2 board, giving students a ready-to-build STEM robot set for classroom projects, after-school activities and robot competitions. Batteries are not included.Maqueen Plus...

SKU: DF-DFR0667

This Charger - MicroUSB is designed for single-cell 3.7V lithium battery. With its tiny body, you can easily integrate it into your applications. The charger adopts TP4056X lithium battery charging IC, which guarantees you quick and safe charging. Three output current modes can be easily switched...

SKU: DF-ROB0148 · MPN: ROB0148-EN

Maqueen Lite is a compact, pre-assembled robot for the BBC micro:bit, and the friendliest way into classroom robotics. Slot a micro:bit into the edge connector, write a few blocks in MakeCode, and it drives, follows a line, flashes its headlights and beeps. No soldering and no chassis to build. ...