All Products

SKU: SF-SEN-13266

The SparkFun MAX31855K Thermocouple Breakout is a simple 14-bit resolution, SPI-compatible, serial interface thermocouple digitizer that makes reading a wide range of temperatures possible. A thermocouple works by taking two wires made of dissimilar metals, connecting them at the two ends, and...

SKU: AF-269

The MAX31855 Thermocouple Amplifier Breakout converts K-type thermocouple readings into digital data via SPI, handling cold-junction compensation automatically. It measures temperatures from −200°C to +1350°C in 0.25°C increments, making it suitable for a wide range of temperature monitoring appl...

SKU: DF-DFR0558

This Gravity I2C high-temperature sensor pairs a signal amplification module (MAX31855K) with a stainless steel sheathed K-type thermocouple probe for measuring temperatures up to 800 °C. The module converts the thermocouple's millivolt signal to a 14-bit digital reading over I²C, with cold-junct...

SKU: SF-SEN-16295

The MCP9600 Breakout is a high accuracy Thermocouple Amplifier equipped with an I2C interface, accessed over our Qwiic system. Inside the chip are two temperature sensors, one for the thermocouple itself (the hot junction) and one for the chip itself (the cold junction). As a result, the MCP9600 ...

SKU: SF-SEN-16294

The MCP9600 Breakout is a high accuracy Thermocouple Amplifier equipped with an I2C interface, accessed over our Qwiic system. Inside the chip are two temperature sensors, one for the thermocouple itself (the hot junction) and one for the chip itself (the cold junction). As a result, the MCP9600 ...

SKU: AF-270

A Type-K thermocouple with fiberglass braid insulation, rated to 500°C — far beyond the ~200°C limit of standard vinyl-insulated thermocouples. The bare bead probe design is suited to measuring both air and surface temperatures in high-heat environments such as ovens, kilns, heaters, and industri...

SKU: AF-4101

The Adafruit MCP9600 I2C Thermocouple Amplifier handles all the analogue complexity of thermocouple measurement for you. Simply connect your thermocouple, wire up I2C, and read accurate temperature data from virtually any thermocouple type — K, J, T, N, S, E, B, and R types are all supported. Th...

SKU: AF-5165

The Adafruit MCP9601 (MCP96L01) I2C Thermocouple Amplifier handles all the analogue complexity of thermocouple measurement over a simple I2C interface. Connect your thermocouple, wire up I2C (or use the solderless STEMMA QT connector), and read accurate temperature data from K, J, T, N, S, E, B, ...

SKU: DF-SEN0656 · MPN: SEN0656

The CT1780 is a cold-junction compensated amplifier for K-Type thermocouples, designed to make extreme temperature measurement easier to add to microcontroller projects. It digitises the tiny thermocouple signal and provides temperature readings with 0.25℃ resolution over a very wide measurement ...

SKU: SF-SEN-14843

It’s time to say hip hip array for this IR Breakout! The MLX90640 SparkFun IR Array Breakout is equipped with a 32x24 array of thermopile sensors creating, in essence, a low resolution thermal imaging camera. With this breakout you can detect surface temperatures from many feet away with an accur...

SKU: SF-SEN-11859

This is not your typical temperature sensor. The TMP006 Breakout can measure the temperature of an object without making contact with it. By using a thermopile to detect and absorb the infrared energy an object is emitting, the TMP006 Breakout can determine how hot or cold the object is. The TMP0...

SKU: SF-SEN-13715

This is a stainless steel, Type-K Thermocouple probe. A thermocouple works by taking two wires made of dissimilar metals, connecting them at the two ends, and making a temperature gradient between one end and the other (a ‘hot’ end and a ‘cold’ one). Once this is achieved, a voltage potential is ...

SKU: SF-SEN-00251

36" high temperature Type-K Thermocouple with glass braid insulation.

SKU: AF-3245

Thermocouples are best used for measuring temperatures that can go above 100°C. This is a bare wires stainless-steel tip probe which can measure air or surface temperatures. Most inexpensive thermocouples have a vinyl covering which can melt at around 200°C, this one uses a fiberglass braid so...

SKU: SF-SEN-13763

A low-cost, highly accurate digital humidity and temperature sensor breakout board based on the Silicon Labs Si7021. Communicates over I²C with just two data lines, providing relative humidity and precise temperature readings for environmental monitoring projects. The breakout includes built-in ...

SKU: AF-3895

Thermocouples are best used for measuring temperatures that can go above 100°C. This is a bare-wire bead-probe which can measure air or surface temperatures. Most inexpensive thermocouples have a vinyl covering which can melt at around 200°C, this one uses a fiberglass braid so it can be used ...

SKU: SF-SEN-14607

Get ready to be able to see like the Predator! The SparkFun Grid-EYE Infrared Array Breakout board is an 8x8 thermopile array, meaning you have a square array of 64 pixels capable of independent temperature detection. It’s like having a thermal camera, just in a lower resolution. To make it ...

SKU: SF-SEN-12064

The HTU21D is a low-cost, easy to use, highly accurate, digital humidity and temperature sensor. This sensor is ideal for environmental sensing and data logging and perfect for a weather stations or humidor control systems. All you need is two lines for I2C communication and you’ll have relative ...

SKU: AF-5870 · MPN: ADA5870

This compact breakout adds a high-resolution, single-channel ADC to your I2C bus, making it a handy choice for precision differential measurements. It is built around the MCP3421, a simple and low-cost 18-bit ΔΣ converter with adjustable gain, a built-in precision reference voltage, and support f...

SKU: SF-BOB-09966

A simple breakout board for the USB Mini-B connector, bringing all 5 pins out to a breadboard-friendly 0.1" pitch header. Useful for prototyping USB connections or as a convenient 5V power source (up to 100 mA, unregulated). Key Features All 5 Pins Broken Out – VCC, D-, D+, ID, and GND Breadb...