All Products

SKU: SF-ROB-14451

The SparkFun TB6612FNG Motor Driver breakout can independently control up to two DC motors at a constant current of 1.2 A (3.2 A peak). Each motor channel supports four modes — clockwise, counter-clockwise, short-brake, and stop — controlled via two input signals and a PWM speed input. All pins ...

SKU: SF-ROB-14450

The TB6612FNG Motor Driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes: CW, CCW, short-brake and stop. The two motor outputs (A and B) can be separately controlled, and t...

SKU: DF-DFR0502

Gravity IO Expansion Shield with Motor Driver is a new product designed for Arduino Boards. It combines IO Expansion Shield and DC Motor Driver Shield, equipped with Gravity sensor interface and TB6612FNG dual motor driver. It also has XBee socket, I2C interface and UART po...

SKU: SF-DEV-14285

The SparkFun Wireless Motor Driver Shield is designed to make connecting motors, sensors and other components to your Arduino-based project as fast and easy as possible. The heart of the Wireless Motor Driver Shield is the Toshiba TB6612FNG H-Bridge Motor Driver, which allows the shield to contro...

SKU: DF-DFR0592

The DC Motor Driver HAT is a Raspberry Pi add-on board that drives up to two DC motors via I2C. Built around the TB6612FNG motor driver chip with 1.2 A continuous current per channel (2 A peak), it supports both standard DC motors and motors with encoders through the on-board encoder interface. ...

SKU: SF-ROB-09571

The SparkFun Serial Controlled Motor Driver allows you to control up to two DC motors using a serial command interface. The serial interface is easy to use and it lets the user select an individual motor, the direction, and the desired speed constant (up to 10 different speed from stop to full sp...

SKU: DF-DFR1136 · MPN: DFR1136

This DFRobot motor driver carrier board is purpose-built for the UNIHIKER M10, featuring a tilted edge connector slot that positions the screen at an optimal viewing angle. It integrates a dual 3 A DC motor driver with separate motor power, plus onboard RGB LEDs and infrared transmitter/receiver....

SKU: DF-DRI0001

The DFRobot 2×1A DC Motor Shield uses the L293 motor driver chip to control two 7–12 V DC motors at up to 1 A per channel. It stacks directly onto Arduino Uno and Arduino Mega boards, using pins 4, 5, 6, and 7 for motor control with PWM speed support. Key Features Dual Motor Drive – Control tw...

SKU: SF-ROB-22727 · MPN: ROB-22727

The SparkFun XRP Controller is the brain of the Experiential Robotics Platform (XRP), a hands-on educational robotics system designed for middle and high school students. Built around a Raspberry Pi Pico W, it provides WiFi and Bluetooth connectivity, a 6-axis IMU, dual motor drivers, and a Qwiic...

SKU: DF-DRI0041

An ultra-compact dual DC motor driver built around a robust H-bridge design with 7 A continuous current per channel and a 50 A peak rating. Opto-coupler isolation on all control signals protects your microcontroller from motor-induced reverse currents, while built-in UVLO (Under-Voltage Latch-Out...

SKU: MB-12040

This encoder motor is capable of driving two DC motors or one encoder motor. It has 16 pins, allowing you to connect with MegaPi by simply plugging in. The motor driver IC on the board is TB6612, which is a high efficiency MOSFET driver with low heat dissipation. Overcurrent protection included t...

SKU: WS-24004

Raspberry Pi Pico Entry-Level Sensor Kit Including 15 Common Modules Such As LED, Button, Buzzer, Etc.Out Of The Box As A Whole Kit, Or Can Be Separated To Use Independently Comes With Online Development Resources And Manual Features At A Glance Standard Raspberry Pi Pico header, supports Raspber...

SKU: SF-COM-00315

The SN754410 is a quad half H-bridge motor driver IC capable of driving DC motors, stepper motors, and other inductive loads. It accepts TTL 5V logic inputs and can drive motors from 4.5V to 36V at up to 1A continuous output current per channel. A pin-compatible replacement for the popular L293D...

SKU: DF-DRI0039

INTRODUCTION The latest quad motor driver shield for Arduino, compatible with 5V/3.3V Arduino controller, can control up to four DC motors with 8 pins at the same time. The shield supports PWM speed control and polarity control. The driver shield includes two TB6612FNG ...

SKU: SF-DEV-10618

The SparkFun Power Driver Shield Kit lets you switch high-current loads directly from your Arduino using six RFP30N06LE N-channel MOSFETs. Connect a computer power supply or other DC source to drive motors, solenoids, LED strips, and other power-hungry devices with PWM control. Each of the six c...

SKU: SF-ROB-16328

The SparkFun Auto pHAT is an all-in-one robotics add-on for the Raspberry Pi. It drives up to two DC motors (with optional encoder support) and four servo motors, all controlled over I2C — leaving your Pi's GPIO pins free for other uses. A Qwiic connector is included for easy expansion. The boar...

SKU: SF-KIT-21301

A note for SparkFun Inventor's Kit v4.1 users: The only change that was made from the SIK v4.1 to the SIK v4.1.2 is our new carrying case. All of the internal parts and instructional guide have remained the same! The SparkFun Inventor's Kit (SIK) is a great way to get started with programmi...

SKU: KS-KS0428

The Keyestudio Mini Tank Robot V2.0 is a tracked robotics platform for learning Arduino programming, sensor integration, and smart robot construction. It supports obstacle avoidance, line following, IR remote control, Bluetooth app control, ultrasonic following, and facial emoticon display — all ...

SKU: SF-KIT-18577

The SparkFun Tinker Kit (STK) is a great way to get started with programming and hardware interaction with the Arduino programming language. This latest version of the STK adds in the Qwiic functionality. Each SparkFun Tinker Kit includes everything you need to complete 11 circuits that will t...

SKU: SF-PRT-14411

The SparkFun LiPo Charger/Booster is a compact board that charges a single-cell lithium polymer battery and boosts its output to a regulated 5V at up to 1A. Built around the MCP73831 charge controller and PAM2401 boost converter, it's an economical solution for powering 5V projects from a LiPo ce...