All Products
Showing 1-9 of 9 products · 7 unavailable products hidden
![Muscle Sensor Surface EMG Electrodes - H124SG Covidien [Pack of 6]](/rails/active_storage/representations/redirect/BAh7BkkiC19yYWlscwY6BkVUewdJIglkYXRhBjsAVGkCr4ZJIghwdXIGOwBUSSIMYmxvYl9pZAY7AEY=--0216f6846afa24186e1573fc5b39450260cf8bad/BAh7BkkiC19yYWlscwY6BkVUewdJIglkYXRhBjsAVHsHOgtmb3JtYXRJIghqcGcGOwBUOhJyZXNpemVfdG9fZml0WwdpApABaQKQAUkiCHB1cgY7AFRJIg52YXJpYXRpb24GOwBG--4cc5678865497cdbcf7b02aee5242eda5f847322/image_6959a3e0-09ab-4da1-8a97-3ab126f211f2.jpg)
Muscle Sensor Surface EMG Electrodes - H124SG Covidien [Pack of 6]
Have your next project be controlled by your muscles with this pack of Muscle Sensor Surface EMG Electrodes! Pair the electrodes with the MyoWare Muscle Sensor and a microcontroller (ie. Arduino, or anything else with analog input reading ability) to create a DIY low-cost v...
MyoWare 2.0 Power Shield
·
The MyoWare® 2.0 Power Shield is designed to easily power the MyoWare 2.0 Muscle Sensor for remote applications. The MyoWare Power Shield is equipped with snap connectors on the board so you can easily stack it to the top side of the MyoWare Muscle Sensor. Flip the switch to the ON position to gi...
Stackable Header - 3 Pin (Female, 0.1)
This is a simple 3 pin female PTH header. This header is in a configuration that makes it ideal to be used with the MyoWare Muscle Sensor line. Each pin has a spacing of 0.1" in between each other. Documents: Datasheet
MyoWare 2.0 Muscle Sensor
·
Control a project with muscle activity instead of buttons, levers or joysticks. The MyoWare® 2.0 Muscle Sensor is an all-in-one surface electromyography (sEMG) sensor that detects the electrical signals generated when a muscle flexes, then outputs an analogue signal representing the strength of t...
MyoWare 2.0 Reference Cable
The MyoWare 2.0 Reference Cable extends the reference pin on the MyoWare 2.0 Muscle Sensor, allowing you to place the reference electrode on a separate part of the body. This is useful when the sensor's built-in reference pin cannot reach a suitable location, such as a bony portion of the elbow o...
MyoWare 2.0 Arduino Shield
The MyoWare® 2.0 Arduino Shield is designed to easily connect up to six MyoWare 2.0 Muscle Sensors and Link Shields using 3.5mm TRS-to-TRS audio cables. The board comes pre-populated with male headers so all you would need to do is stack it on your Arduino and connect the sensors to read up to si...
MyoWare 2.0 Cable Shield
The MyoWare® 2.0 Muscle Sensor is designed to be wearable, allowing you to attach biomedical sensor pads directly to the board itself. However, there still may be cases where you want to mount the sensor pads away from the board; this is where the MyoWare 2.0 Cable Shield comes in. The shield inc...
MyoWare 2.0 Reference Cable - 10 pack
This is a 10 pack of the MyoWare® Reference 2.0 Cables. The MyoWare 2.0 Reference Cable is meant as an extension for the MyoWare 2.0 Muscle Sensor's reference pin. You will just need to insert the pin into its housing and place a biomedical sensor pad into the electrode snap. When ready, stick th...
MyoWare 2.0 Wireless Shield
·
The MyoWare® 2.0 Wireless Shield is designed to take in readings from the MyoWare 2.0 Muscle Sensor and wirelessly transmit sensor data with the ESP32-WROOM! This shield also includes a built-in LiPo battery to remotely power the muscle sensor and the ESP32 module. The Wireless Shield is equipped...
