All Products

SKU: PL-1152

An enclosed battery holder for three AA cells with a built-in on/off switch. The snap-on lid slides over the batteries to fully enclose them, keeping the cells secure during use. Provides approximately 4.5 V with three alkaline AA batteries (3 × 1.5 V) or 3.6 V with three NiMH rechargeable cells...

SKU: AF-875 · MPN: 875

This 8×AA battery holder provides a portable power source with a built-in on/off switch and a standard 5.5 mm / 2.1 mm DC barrel plug for easy connection to Arduino boards, LED strips, motors, and other 12V devices. Use alkaline AAs for approximately 12V at 3000–4000 mAh, or rechargeable NiMH cel...

SKU: DF-FIT0918

A compact 4×AA battery holder with a built-in on/off power switch, DC2.1 barrel jack output, and a protective cover. Ideal for powering Arduino, Raspberry Pi, and other microcontroller projects with a portable 6V supply. The holder accepts four standard AA batteries (1.2V rechargeable or 1.5V al...

SKU: AF-3286 · MPN: 3286

A slim 3×AAA battery holder with a built-in on/off switch, JST 2-pin connector, and an ergonomic belt clip. The series configuration outputs approximately 3.6–4.5V — a similar range to lithium-ion batteries — making it an ideal non-rechargeable alternative for 3.3V projects that use a JST battery...

SKU: AF-3788 · MPN: 3788

A 4×AA battery holder with a built-in on/off switch and a 13cm (5″) power cable terminating in a centre-positive 2.1mm DC barrel jack. Provides convenient portable power with easy switching for development boards and projects that accept a standard DC barrel jack input. Delivers approximately 4....

SKU: SF-PRT-14219

A 2×AAA battery holder with a sliding cover and built-in ON/OFF switch. The cover keeps batteries secure, and the switch provides convenient power control for your project. Wire leads are approximately 150 mm long with 5 mm tinned ends. Specifications Capacity – 2× AAA batteries (3 V total) S...

SKU: IT-IM120720001

Add a tidy power source to your battery-powered project with this holder for two AA cells. It provides around 3V from 2 x 1.5V batteries, making it suitable for many small electronics builds.The holder has a removable sliding cover secured with a small Phillips head screw, helping keep the cells ...

SKU: AF-4193 · MPN: 4193

A slim 2×AA battery holder with a built-in on/off switch and genuine JST PH connector. Two AA batteries in series provide approximately 3V — ideal for powering low-voltage electronics projects, microcontrollers, and portable builds without needing to disconnect the battery to turn off power. The...

SKU: LB-LS3337

An enclosed battery holder for three AAA cells with a built-in on/off switch. The snap-on lid fully covers the batteries, keeping them secure during use. Wire leads allow you to connect directly to your project. Three AAA cells in series provide approximately 4.5V (alkaline) or 3.6V (NiMH), suit...

SKU: AF-830 · MPN: 830

A 4×AA battery holder with a snap-on cover and built-in on/off switch. Holds four AA batteries in series, outputting a nominal 6V (alkaline) or 4.8V (NiMH), making it a convenient portable power source for 5V microcontroller projects. With alkaline batteries, you may want to add a 1N4001 diode i...

SKU: DF-FIT0625 · MPN: FIT0625

This compact battery holder is a handy portable power pack for small electronics and maker projects. It holds two AAA batteries and connects them in series, making it suitable for projects that need a simple removable battery supply.The holder includes a cover and an integrated power switch, so y...

SKU: PI-COM1305

A compact 2×AAA battery holder with a built-in power switch and JST connector, compatible with micro:bit and other boards that accept JST battery inputs. This is the same battery holder included in our micro:bit accessories kit. Key Features Power Switch – On/off switch for convenient power co...

SKU: SF-PRT-10512

A snap-in 9V battery holder with a 5.5mm/2.1mm centre-positive barrel jack connector. The battery clicks securely into place, and three mounting holes allow you to attach the holder to an enclosure or chassis. Key Features Snap-In Design – Battery clicks securely into place 5.5mm/2.1mm Barrel...

SKU: SF-DEV-11893

The LilyPad Simple Power is a simple e-textile board that lets you connect and charge a lipo battery and switch it on or off, that’s it! We provide you with a JST connector and a slide switch, you supply the battery and sewing skills! With this LilyPad Simple Power, you should find no trouble in ...

SKU: AF-3951 · MPN: 3951

A 2×AA battery holder with a built-in knife switch for controlling power. Unlike typical slide switches, the knife switch provides a clear visual indicator of open and closed circuit states — making it an excellent tool for teaching basic electronics and circuit concepts. The holder takes two AA...

SKU: SF-PRT-18769

This 3xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover as well as an ON/OFF switch that can be used to control power to your project. The 6" (~150mm) cable has been terminated with a JST connector. Note: Please keep in...

SKU: SF-PRT-12083

This 4xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover, which is secured with a small phillips head screw. Another bonus is the ON/OFF switch which can be used to control power to your project.The leads are about 150mm...

SKU: SF-PRT-10891

This 3xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover, which is secured with a small phillips head screw. Another bonus is the ON/OFF switch which can be used to control power to your project.The leads are about 150mm...

SKU: SF-PRT-09925

This 2xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover, which is secured with a small Phillips head screw. Another bonus is the ON/OFF switch which can be used to control power to your project. The leads are about 1...

SKU: LB-LR0295

A simple 9V battery holder with a DC barrel connector. Provides a convenient way to mount and connect a 9V battery to your electronics projects. Key Features DC Barrel Connector – Standard connector for easy integration Snap-In Battery Mount – Holds a 9V battery securely Also Available 9V...